Chapter 4 Adjustments and settings for recording
4-2-3 Setting the synchro scan modeItems to be set and what is set
The signals to be recorded are selected using REC SIGNAL.
Proceed with operation by following the steps below.
CAM:The signals from the camera are recorded.
VIDEO: The signals from the GENLOCK IN connector are
Press the SHUTTER switch from ON to SEL to establish
1
recorded.
the SYNCHRO SCAN mode.
The images may be disrupted when the signals
SYNCHRO SCAN (+ and �) buttonsfrom the GENLOCK IN connector are non-standard
signals.
1394:The signals from the DVCPRO connector are
recorded.
Bear the following points in mind when 1394 is selected
as the setting.
O Connect the unit to external units on a 1-on-1 basis.
O The sound is recorded using the audio signals supplied to
the DVCPRO connector but its input level cannot be
adjusted.
At a time like this, nothing is recorded on the cue track.
O The cue signals cannot be input or output.
O When the TCG switch is at the F-RUN position, the time
code supplied to the DVCPRO connector is recorded.
SHUTTER switchO When the TCG switch is at the R-RUN position, the
recording is performed using the time code which has been
In the SYNCHRO SCAN mode, it is possible to changerecorded on the tape.
2
the shutter speed continuously within a range from 1/60.3O When EXT is selected as the UB MODE item setting on the
sec. to 1/249.7 sec. by operating the SYNCHRO SCAN (+<TC/UB> screen by performing menu operations, the user
and �) buttons.bits which are supplied to the DVCPRO connector are
recorded.
O The user bits which are supplied to the DVCPRO
connector are recorded in the vertical blanking period
4-3 Selecting the recording signalsregardless of the VITC UB MODE item setting.
and recording systemO It is not possible to record the time code which is supplied
to the TC IN connector.
O The time code which is output from the TC OUT connector
With this unit, both the signals to be recorded and the
is not synchronized with the video output signals or the
recording format can be selected.
output signals from the DVCPRO connector.
O The signals which are output from the VIDEO OUT
4-3-1 Selecting the recording signals
connector, MON OUT connector or AUDIO OUT connector
differ from the actual signals. Use them for monitoring
Open the <SYSTEM MODE> screen from the SYSTEM
purposes.
SETTING page and select the signals to be recorded using
O It is not possible to use the GENLOCK IN connector to
the CAMERA MODE item by performing menu operations.
achieve synchronization with the external reference signal.
O The signals may be disrupted when the power of the
SDC905connected units is switched from ON to OFF or vice versa
or when the interface cable is connected or disconnected.
#< SYSTEM MODE >
O It may take several seconds for the system to stabilize
REC SIGNAL :CAMimmediately after the input signals are switched or
REC MODE :16:9/50Mimmediately after the operation mode is changed, for
SET UP 50 :7.5%A
SET UP 25 :7.5%Ainstance.
PB MODE :AUTO
Wait until the system has stabilized before proceeding with
REC TALLY :RED
recording.
O Supply normal playback speed (1k speed) signals. When
SDC615playback signals of any other speed are supplied, the
images and sound may not be recorded properly.
#< SYSTEM MODE >
O The pre-recording function SDC905 and Interval REC
function do not work.
REC SIGNAL :CAM
ASPECT :16:9O Characters other than the ones that are used in the menus
SET UP :7.5%A
are not displayed on the viewfinder screen and output
PB MODE :AUTO
REC TALLY :REDimages.
Similarly, the same are not displayed when VIDEO is
selected.
30 |
ACEC
