Parts and their functions
GR, G, B gain controls [R, G, B GAIN]MIris/master pedestal control joystick [IRIS/PED]
These are used for the red (R), green (G) and blue (B)The iris level of the lens is adjusted by moving the joystick up
adjustments of the white balance. When the auto whiteand down, and the master pedestal is adjusted by turning it.
balance can be performed and the R, G or B gain control isWhen in the auto iris mode:
turned, the gain control value on the LCD display changes.The iris can be adjusted manually.
When not in the auto iris mode:
HR, G, B black controls [R, G, B FLARE]The auto iris level is adjusted.
Whether these controls are to be used to adjust the flare or
Since the master pedestal adjustment is independent of the
pedestal can be set on the menu. They are used for the red
R, G and B pedestal adjustments, the R, G and B pedestal
(R), green (G) and blue (B) black adjustments. When the
adjustment values remain unchanged even when the master
auto black balance can be performed and the R, G or B
pedestal is changed.
black control is turned, the flare or pedestal control value on
the LCD display changes.
NIris active switch [IRIS ACTIVE]
This makes it possible to adjust the iris. When its lamp is off,
IDTL control [DTL]the iris cannot be controlled from this panel. If the switch is
This is used to increment or decrement (paint) the detailset to ON and the iris priority is returned to this panel, the
control settings (H-DTL and V-DTL adjustment values whichpanel can then exercise iris control.
are set on this panelOs LCD display).
By setting this panelOs DTL HD and SD switches, the effect of
OMaster pedestal active switch [M-PED ACTIVE]
the DTL control can be applied to the HDTV video output or
This is used to activate the master pedestal control functions
SDTV video output.
of the joystick. Its lamp lights when the functions are
activated.
JIris joystick control range selector switch [FULL]
This is used to set the control range of the iris joystick toPCall switch [CALL]
FULL (when the switch lamp is lighted: from open to close).
This is pressed to call the camera. While it is held down, the
When the switch lamp is off, the control range of the SENSE
lamp of the cameraOs call switch lights and the buzzer
control T is used for control.
sounds. After the switch is released, the buzzer stops.
If the call switch on the camera has been pressed, the lamp
KAuto iris switch [AUTO]of this switch remains lighted while that switch is held down.
This is used to activate the auto iris function. Its lamp lights
in the auto iris mode.QAlarm display [ALARM]
When the lamp is off, use the Iris/master pedestal control
This lights when optical transmission is not going
joystick M to control the lens iris.
satisfactorily or when a problem has occurred in the camera,
CCU fan or power supply.
Q P L
RLens extender display [LENS EXT]
PED
IRISThis lights when the setting of the lens extender is other than
ACTIVEALARMCALLIRIS
N1a.
M-PEDACTIVELENSEXT
Lighted: The setting of the lens extender is other than 1a.
O
X0.8Off:This indicates that the lens extender is not being
R
used or that the extender function is not available.
SPEDSENSE
M
V
SLens ratio effect [a0.8]
IRISRANGE
This lights when the cross converter is inserted into the lens.
W
TIris sensitivity control [SENSE]
This is used to adjust the iris control range of the joystick.
UT
UIris control range control [RANGE]
LTally indicators
This is used to adjust the iris control position (shift the control
The red tally indicator is at the top and the green tallyrange) of the joystick.
indicator is at the bottom. They light when the respective
tally signals are input to the INCOM/tally connector on the
VMaster pedestal level indicator
CCU.
This indicates the master pedestal level in the range of -99 to
99.
WIris f-number indicator
This indicates the lens f-number.
15 |
ACEC
