Parts and their functions
Black gamma control switch [BLK GAMMA CONTROL]BRIGHT:Dot matrix display brightness setting
This is operable when the lamp of the BLK GAMMA ONThis is used to set the brightness of the
switch among the MODE ON/OFF switches is lighted. Itdot matrix display.
is selected to adjust the black gamma curve.BUZZ:Buzzer setting
When the switch is selected, its lamp lights.This is used to set the buzzer to ON or
BLKR, BLKM, BLKB GAM:OFF.
Black gamma curve (R, MASTER or B)<CARD>:SD card read/write setting
Adjustment range: �32 (black compression) toThis is used to write the cameraOs data
+31 (black expansion)on the SD card or read it from the card.
LEVEL: Black gamma level
Setting: LOW (brightness level: approx. 20%),System switches [SYSTEM]
HI (brightness level: approx. 30%)These are the system setting switches used to set the
down-converter mode, select the down-converter filter,
Matrix control switch [MATRIX CONTROL]select GBR or YPbPr for the HDTV video output, select
This is pressed to change the correction amounts for theGBR or YPbPr for the SDTV video output, select the up-
R-G, R-B, G-R, G-B, B-R and B-G chroma saturation.converter mode, select whether the CCU waveform
monitor control connector is to be used for SDTV or
MTX 12, SATU, PHASEHDTV applications, and so on.
These are used to select the following 12-axis matrixHEAD, CCU RCV LEVEL:
adjustment items: G, G_Cy, Cy, Cy_B, B, B_Mg, Mg,Camera head, CCU unit light reception
Mg_R, R, R_Ye, Ye and Ye_G.strength level displays
These indicate the light reception
strength margins of the camera head andFUNC switches [FUNC]
CCU.ALC LEVEL: Auto iris level
RET1, RET2, RET3, RET4: Return video settings
This is used to adjust the auto iris level of
These are used to set the inputthe lens iris.
allocations of the return signals.SPEED:Auto iris speed
D/C MODE:Down-conversion system selection
This is used to select the down-This is used to set the feedback speed of
the auto iris.
conversion system.WINDOW:Auto iris window
U/C MODE:Up-conversion system selectionThis is used to set the image detection
This is used to select the up-conversion
system.area window of the auto iris.
PEAK:Peak/average setting
D/C LINK:Down-conversion linkThis is used to set the ratio between the
This is used to decide whether to go withaverage and peak values of the auto iris
the down-conversion system control
image detection.
based on the AUX external input or setFAN POWER: Fan power switch
the down-conversion independently.This is used to set the power of the
U/C LINK:Up-conversion link
This is used to decide whether to go withcamera headOs fan to ON or OFF.
FAN SPEED: Fan speed
the up-conversion system control that isThis is used to set the speed of the
linked to the down-conversion system orcamera headOs fan.
set the up-conversion independently.
HD BAR:HD color bar made setting2D-M:Component 2-dimensional low-pass filter
This is used to set whether to apply the
This is used to select the HD color bar2-dimensional low-pass filter to the
mode.SDTV component output.
SD BAR:SD color bar mode setting
2D-E:Composite 2-dimensional low-pass filter
This is used to select the SD color barThis is used to set whether to apply the
mode.2-dimensional low-pass filter to the
PATHO:Pathological pattern output
This is used to forcibly output theSDTV composite output.
COMB:Comb filter mode
pathological pattern.This is used to set the comb filter mode.
SET UP:Color bar setup settingSETUP MODE: Auto setup mode setting
This is used to set the color bar setup.
OUTPUT SEL: Output selectionThis is used to select the auto setup
mode setting.
This is used to set the analog output ofREF FILE:File select
the CCU to RGB or YPbPr.This is used to select the file attribute to
MONI SEL:Monitor switch selection setting
be referenced when auto setup has been
This is used to set the monitor switchstarted.
selection to PM, WFM or the PM-WFMMPED SET:Auto setup MPED convergence value
link mode.
This is used to set the position where the
master pedestal is to be converged when
auto setup has been started.
7 |
ACEC
