HOW TO USE OSETUP MENU� (cont'd)
ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS
1. FUNCTION SETTING
Item: CONTRAST
Selects the colour system and
Adjustment
displays the monitorOs power- <FUNCTION SETTING>
range: �20 ~ 00 ~ +20
COLOR SYSTEM :AUTO
up time or the total usage time.RUSH DELAY TIME :STD.
HOUR METER X100h :000 Function: For approximate adjustment of the picture
Press the button to display
contrast. Before adjustment, set the CONTRAST
the setting menu illustrated on
knob on the front panel to 0.
the right.
EXIT: MENU ADJUST:- + SELECT:
Item: BRIGHT
Adjustment
range: �20 ~ 00 ~ +20
Function: For approximate adjustment of the picture
Item: COLOR SYSTEM
brightness. Before adjustment, set the BRIGHT
Settings: AUTO/NTSC/PAL
knob on the front panel to 0.
Function: Selects the colour system when using the video
input card.
Item: CHROMA
AUTO : Change NTSC and PAL automatically.
Adjustment
NTSC : Keeps the colour system NTSC.
range: �20 ~ 00 ~ +20
PAL : Keeps the colour system PAL.
Function: For approximate adjustment of the colour
NOTE :Normally select AUTO. However, if the input signal is
density. Before adjustment, set the CHROMA
unstable, select NTSC or PAL.
knob on the front panel to 0.
Item: RUSH DELAY TIME
Item: PHASE
Settings: STD./SLOW
Adjustment
Function: Sets the time when the power supply to the
range: �20 ~ 00 ~ +20
monitorOs circuits (excluding the micro computers)
Function: For approximate adjustment of the picture hue.
starts after the power switch is pressed.
Before adjustment, set the PHASE knob on the
STD. : The power supply starts approx.
front panel to 0.
1 second after the power switch is
pressed.Item: NTSC SETUP
SLOW : The power supply starts approx.Settings: 00/7.5
3.2 seconds after the power switch isFunction: Sets the level of the input NTSC signal.
pressed.00 : Compliant with 0% set-up signal.
NOTE :When turning on many multi-format monitors7.5 : Compliant with 7.5% set-up signal.
simultaneously, it is recommended to use SLOW toNOTE :NTSC SETUP is displayed only when the video input
control rush current.card is installed and an NTSC signal is input.
Item: HOUR METER X100hItem: COMPO. LEVEL
NumberSettings: SMPTE/B75/B00
range: 000 ~ 655Function: Sets the level of the input component signal.
Function: Displays the total usage time of the monitor inSMPTE :Compliant with M2VTR signals.
hundred-hour units.B75:Compliant with Betacam 7.5% set-up
signal.
I When the timer passes 655, it returns to 000.B00:Compliant with Betacam 0% set-up
I The timer does not count the usage time under one hour.signal.
NOTE :COMPO. LEVEL is displayed only when a 480/60i,
480/60p, 576/50i or 576/50p signal is input.
2. PICTURE SUB ADJ.
Performs approximate
Item: sub menu
adjustments using the control <PICTURE SUB ADJ.>Adjustment range/
knobs on the front panel. PressCONTRAST :00
BRIGHT :00 Settings: Same as CONTRAST, BRIGHT, CHROMA,
the button to display theCHROMA :00
PHASE :00PHASE and COMPO. LEVEL/NTSC SETUP.
setting menu illustrated on theNTSC SETUP :00
COMPO.LEVEL :SMPTEFunction: Performs CONTRAST, BRIGHT, CHROMA,
sub menu
right. reset
PHASE or COMPO. LEVEL/NTSC SETUP
NOTE : When the RGB signalEXIT: MENU ADJUST:- + SELECT:settings in a single-line display. The sub menu
is input, onlydisplay varies depending on the selected item.
CONTRAST and
Item: reset
BRIGHT are displayed. When the PAL signal is
Function: Sets the CONTRAST, BRIGHT, CHROMA,
input, only CONTRAST, BRIGHT and CHROMA are
PHASE and COMPO. LEVEL/NTSC SETUP
displayed.
values to factory-preset ones.
14
ACEC
