Main Menu (continued)
VIDEO CONFIG
The underlined values are factory preset setting values.
Sub menuSettingsExplanation
GAMMA <NORMAL>Used to select the gamma curve.
*2*1
SELECT<FILM>When FILM is selected, mark is displayed in the top
left of the screen.
*2
FILM GAMMA<VARICAM>Used to select the type of FILM gamma mode.
<OTHER><VARICAM> VARICAM use
<OTHER>When using other types than VARICAM
COLOR TEMP.<USER0-63>*5Used to select the color temperature.
<D93><USER0-63>Adjustable settings 0-63 (color temperature
<D65>around 3000K-9300K)
<D56><D93>Color temperature around 9300K
<VAR1><D65>Color temperature around 6500K
<VAR2><D56>Color temperature around 5600K
*4
<VAR3><VAR1>WB adjustment mode
*4
<VAR2>WB adjustment mode
*4
<VAR3>WB adjustment mode
SHARPNESS <HIGH>*3Used to select the width of the sharpness edge.
*2
MODE<LOW><HIGH>Thin edge<LOW>Thick edge
*2*3
SHARPNESS H<0-30> Used to set the sharpness in the horizontal direction.
When adjusting, the item display moves to the lower part of the
screen.
*2*3
SHARPNESS V<0-30> Used to set the sharpness in the vertical direction.
When adjusting, the item display moves to the lower part of the
screen.
*2
I-P MODE<MODE2>Used to set the mode for IP change.
<MODE1><MODE2>Within Field<MODE1>Normal mode
*2
MONO<OFF>Used to switch between color and monochrome (MONO).
<ON><OFF> Color<ON>Monochrome
* When this is ON, the picture adjusting knob [CHROMA] setting
is fixed at 0.
*2
ANAMO<OFF>If an Anamo lens has been used on the camera, and input through
<ON>SDI 720/60P, 59.94P, the picture is resized to Anamo size
magnification. (a vertically compressed signal can be amplified
vertically and corrected when it is displayed.)
*2
SD ASPECT<4:3>Used for setting the aspect ratio settings when using SD signal
<16:9>input.
<4:3> 4:3 display<16:9> 16:9 display
*2
SCAN<NORMAL>Used to set under-scan and normal display.
<UNDER><NORMAL>Normal display<UNDER>Under-scan
*2
NOISE WIPE<OFF><OFF> This makes a fluid and smooth contrast obtainable.
<ON>This is especially effective for continuously changing the contrast
of the source signal or CG signal when the S/N is very high.
<ON> Noise reduction mode. Depending on the camera, this mode
can be especially effective for dark scenes. We recommend
leaving this setting ?ON? under normal conditions.
*1 Even if FILM gamma is changed during 2 screen display, only the main window is set, and the changes are not
reflected in the sub window.
*2 When ?RGB-COMP.? is selected in ?YPBPR/RGB? in the ?INPUT SELECT? menu (J page 21), this does not operate.
*3 The following sharpness values can each be set,
1) VIDEO system input line (VIDEO,Y/C)(Factory settings are SHARPNESS MODE : LOW,
SHARPNESS H/V : 0)
2) any other input line?s HD (Factory settings are SHARPNESS MODE : HIGH, SHARPNESS H/V : 0)
3) any other input line?s SD (Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0)
and the setting values for the selected input signal from within this group is displayed. The adjustment status is
displayed in the bottom right when selected.
*4 When ?VAR1?, ?VAR2? or ?VAR3? is selected, the monitor switches to WB adjustment mode (J page 17).
*5 When selecting USER0-63
1) Push [ENTER] (USER changes to blue). 2) Select 0-63 with [ , ], and push [ENTER].
16 |
ACEC
