EEE
NNN
Remote Control Unit PreparationInstallation Guide
GGG
LLL
III
SSS
HBattery InstallationHH
Lithium battery
91 Remove the battery holder.(included)WARNING10
Pull the holder by the position B while pushing posi-
Back side
tion A in the direction indicated by the arrow.
This installation information is designed for experienced installers and is not in-
2 Install the battery on the battery holder.
tended for non-technical individuals. It does not contain warnings or cautions of po-
Set a new battery properly with its (i) side facing up
tential dangers involved in attempting to install this product.
as shown in the Ţgure.
3 Insert the battery holder.Position B
Any attempt to install this product in a motor car by anyone other than qualiŢed in-
Push in the battery holder back into its original posi-
staller could cause damage to the electrical system and could result in serious per-
tion.
sonal injury or death.
Battery holderPosition A
Battery Notes
If you encounter problems, please consult your
Remove and dispose of an old battery immediately.P Installation Hardware
nearest professional installer.
Battery Information:
No.ItemDiagram QOty
eBattery type: Panasonic lithium battery (CR2025) (included)Caution:
eBattery life: Approximately 6 months with normal use (at room temperature)1 Mounting collar1
eThis unit operates with a 12 V DC negative
ground auto battery system only. Do not at-
Caution:tempt to use it in any other system. Doing so
2 Hex. nut (5 mm?)1
eImproper use of batteries may cause overheating, an explosion or ignition, resulting in injury or a Ţre.could cause serious damage.
Battery leakage may damage the unit.
3 Rear support strap1Before you begin installation, look for the items
which are packed with your unit.
eDo not disassemble or short the battery. Do not throw a battery into a Ţre.
eKeep batteries away from children to avoid the risk of accidents.4 Tapping screw1
eWarranty Card�Fill this out promptly.
eBe careful to the local disposal rules when you dispose of batteries.(5 mm?a16 mm)ePanasonic Servicenter for Service Directory
�Keep for future reference in case the product
5 Mounting bolt (5 mm?)1
Control Reference Guideneeds servicing.
eInstallation Hardware�Needed for in-dash in-
Buttons of the remote control function in the same way as the controls on the main unit of the reference page.
6 Power connector1
stallation.
Point the remote control unit at the main unitOs sensor (REMOTE).
P Required Tools
7 Removable face plate 1
YouOll need a screwdriver, a 1.5 V AA battery, and
(ATT)case
the following:
Power button (PWR)PWRMUTEMute button (MUTE)
8 Trim plate112 V DC ElectricalSide-cut
(! page 10)(! page 10)
Test bulbtapepliers
Mode button (MODE)MODE
Volume control buttons
(! pages 14, 16)
VOL(VOL " #)
P Overview
(! page 10)
This product should be installed by a professional.
However, if you plan to install this product yourself,
Band/Disc up* buttonPRGBAND/DISC UPyour Ţrst step is to decide where to install it. The
(BAND/DISC UP*)instructions in these pages will guide you throughP Dashboard SpeciŢcations
(! pages 14, 17)the remaining steps: Thickness
TUNE
TRACK(Please refer to the OWARNING� statementMin. 4.75 mm
*Only for CD changerabove.)Max. 5.56 mm
Tune, Track buttons
control
(TUNE % $, TRACK 65)eIdentify and label the car wires.53 mm
(When the CD changer
(! pages 14, 16)eConnect the car wires to the wires of the power
is connected.)
connector.
Car Audio
eInstall the unit in the dashboard.182 mm
eCheck the operation of the unit.
1819
CQ-DF302WCQ-DF302W |
ACEC
