NAME OF EACH PART How to Insert the Batteries
AUTO
HEATCOOL
O ON
Remote Control1 Signal Transmitter2FFAUTODRYAUTOFAN
POWERFULTFAAUTNO
12 Operation DisplayMODE
AUTOAIR SWECONOMY
IN
3 Powerful Mode Operation ButtonON1MANUALGOFF2SLEEFAN SPEEDP
CHEC3
2AUTAUTOHEAHEATCOOLCOOLDRDRYFANAN4 Room Temperature Setting ButtonKRESETCLOCKTIMERCANCELSET
AUTAUTO(self-illuminating button)1.5V
1.5V
AUTAUTO
ON5 Operation Mode Selection Button
OFFAUTAUTOFANAN1
6 Economy Mode Operation Button
TEMP
3OFF/ON7 Vertical Airflow Direction Button
POWERFUL
!
48 ON-Timer Button
5MODEECONOMYSLEEP#1Slide down the remote control cover completely
69 OFF-Timer Button
AIR SWING
FAN SPEED$2Insert the batteries
7$0 Reset Point
123�Be sure the direction is correct
8ONSET%(Press with fine-tipped object to clear the memory)�12.00 at display - flashing
9CANCEL^Y Set the current time (CLOCK) immediately to
OFF! OFF/ON Buttonprevent battery exhaustion.
TIMER&(self-illuminating button)
0CHECKRESETCLOCK* About the batteries
@ Sleep Mode Operation ButtonY Can be used for approximately one year.
(
# Fan Speed Selection Button Observe the following when replacing the
batteries
$ Horizontal Airflow Direction ButtonY Replace with new batteries of the same type.
Y Do not use rechargeable batteries (Ni-Cd).
Remote Control Signal.% Timer Set ButtonY Remove the batteries if the unit is not going to be
Y Make sure it is not obstructed.used for a long period.
Y Maximum distance : 10 m.^ Timer Cancellation Button
Y Signal received sound.
One short beep or one long beep.
& Time-Setting Button
Notes for Remote Control.
Y Do not throw or drop.* Clock Button
Y Do not get it wet.
Y Certain type of fluorescent lamps may affect( Remote Control Cover
signal reception. Consult your dealer.
PREPARATION BEFORE OPERATIONHOW TO OPERATE Setting Temperature
Y Press 3 to increase or decrease the temperature.
Y The temperature can be set between 16!C ~ 30!C.
Indoor UnitY Recommended temperature:
AAUTUTOHHEAECooling ModelHeat Pump Model
CCOOLAT
OO
212AUAUTTOAAUTOLDRRUYTOFAANNCOOL � 26!C ~ 28!CCOOL � 26!C ~ 28!COFFND
POWERFULFAAUTTEMAANNUTO
DRY � 1!C ~ 2!CDRY � 1!C ~ 2!C
6P3EODMlower than thelower than the
35ECONOMYOAIR SFF/Oroom temperatureINGWNroom temperature
1
5 4ON1SLEHEAT � 20!C ~ 24!C2EP
N SPEED4Y During AUTO Operation, press 3 to select:-FA6
1Connect the power supply cord to an independentY Operation with 2!C higher than the standard
power supplytemperature.
To start the operation
Y Operation with the standard temperature.
2Open the front panelY Press 1.
Y POWER indicator (green) on the indoor unit will light
up.Y Operation with 2!C lower than the standard
3Remove the air filtersY To stop, press once more.temperature.
Setting Mode Standard Temperature
4Fit the air purifying filters in placeY Press 2 to select:-
Cooling Model
5Insert the air filters
IndoorStandard
Cooling ModeltemperatureOperationtemperature
6Close the front panelCooling25!C
AUTO � Automatic Operation
COOL � Cooling Operation23!CSoft Dry22!C
Remote ControlDRY� Soft Dry Operation
�To set the current timeFAN� Air Circulation OperationY Once the Automatic Operation is selected, the indoor
AIR SWINGtemperature sensor operates automatically to select
FAN SPEEDthe desired operation mode with Cooling or Soft Dry.
123Heat Pump ModelY After the operation mode has been selected, the
ONSETmode does not change.
AUTO � Automatic Operation
OFFCANCELHEAT� Heating OperationHeat Pump Model
TIMER2COOL � Cooling Operation
IndoorStandard
RESETCLOCK1DRY� Soft Dry OperationtemperatureOperationtemperature
Cooling25!C
23!CSoft Dry22!C
1Press 1.20!CHeating21!C
2Then press 2 to increase or decrease the time.
Y At the beginning of the automatic operation, Heating,
3Press 1 again.Cooling or Soft Dry is automatically selected according
Set time at display will light up.to the indoor temperature.
Y The operation mode changes every hour, when
necessary. |
ACEC
