REMOTE CONTROL OPERATION
Programming The Remote Control
The Universal Remote Control can be programmed toProgramming Without A Code
operate many manufacturers? components using the
This procedure searches all codes and is called the
component function buttons for VCR, DVD, AUX, RCVR,
?sequence method.?
DTV CABLE or DBS. Follow the procedures for
1. Confirm that the external component is plugged in and
programming your Remote Control with or without a code
on.
for the component.2. Turn the component off.
Default Modes for Remote ControlACTION
3. Press and POWERtogether, for at least 5
DeviceOperatesDefault
seconds. After 5 seconds, the illuminated mode
TVTV (Panasonic Only)Panasonic TV Code
(component) buttons will begin to flash. Release the
DTV-STBDTV (Panasonic Only)Panasonic DTV CodeACTION and POWER buttons.
Panasonic CABLE 4. Press the appropriate component button on the Remote
CABLECABLE (Preset)
Code
Control. The component button will illuminate steadily
DBSDBS (Preset) Panasonic DBS Codeand all others will go out.
VCRVCR (Preset)Panasonic VCR CodesENGLISH
5. Press the POWER button to set the remote control to the
DVD/CDDVD and CD (Preset)Panasonic DVD Codes
step and set mode.
Personal Video Recorders, Panasonic Personal
AUX6. Point the remote control towards the component.
Tape and VCR2Video Recorder Code
7. Press VOL X (the mode key will blink three times), then
RCVRAudio receiver (Preset)Panasonic RCVR code
press the Remote Control POWER button to test the
Note: Determine the manufacturer of the component and look
in the table for the code (found on page 16 and 17).component. Continue this process until the proper code
is found. If the procedure was successful, the component
Procedure
will turn on.
1. Confirm that the external component is plugged in and
Note:Each time you press the VOL X button, make sure that the
operating.
component key blinks twice before pressing the POWER
2. Turn the component off.
button.
ACTION
3. Press and POWER together for at least 5ACTION
8. Once the device responds, press to store the
seconds. After 5 seconds, the illuminated mode
code. The mode (component) button will blink twice.
(component) buttons will begin to flash. Release the
Note: It may take many attempts before the correct code
ACTION and POWER buttons.
isfound. If you miss a code, press W VOL, then press
4. Press appropriate component button on the Remote
Control: VCR, DVD (CD), AUX (VCR2 or TAPE),the POWER button to test the component.
RCVR, DTV, CABLE or DBS. The component button
will illuminate steadily and all others will go out.Component Codes
5. Enter the 3-digit component code using the Remote
Control numeric keypad (0 ~ 9 buttons). The componentThe Universal Remote Control is capable of operating
button will blink twice.many component brands after entering a code. Some
components may not operate because the codes are not
6. Press the Remote Control POWER to test the
available due to limited memory. The Universal Remote
component. If the procedure was successful, the
Control does not control all features found in each model.
component will turn on and the component key will blink
twice and then go out.
Note: If the component does not operate with the RemoteWrite the code numbers from tables in this space.
Control, repeat the steps 3 through 6 using another codeThis will serve as a reference if you need to program
your Remote Control.
(some brands have multiple codes). If an incorrect code
is entered, or if the procedure takes longer than 30 VCR DVD DVD (CD)
seconds, the programming will fail.
AUX (VCR2) AUX (TAPE) RECEIVER
DTV CABLE DBS
15 z |
ACEC
