rection of your beard. You may gentlyTurn the shaver on and pour somepick), four screws (e), and the
ATTENTION:
increase the amount of pressure aswater over the outer foil.panel cover (f).
2 nickel metal hydride batteries
your skin becomes accustomed toAfter about 10-20 seconds, turn the5. Remove the screw (g) and the
that are recyclable power the prod-
this shaver. Applying excessive pres-shaver off.bottom cover (h).
uct you have purchased. Please
sure does not provide a closer shave.Remove the foil frame and clean it6. Remove the back panel (i).
call 1-800-8-BATTERY for informa-
System outer foiltion on how to recycle the batter-with running water.7. Remove the batteries from the
(see fig. 5)ies.Wipe off any moisture from thebattery block (j).
System outer foil has a slit blade (a)shaver with a dry cloth and remove
WARNING:
the protective cap to allow the sys-
between 2 foils (b). They move up
Do not attempt to replace the bat-
and down independently to follow thetem outer foil to dry completely.
tery for the purpose of reusing the
contours of your face.
Replacing shaving headshaver. This could result in the risk
The slit blade catches and cuts
of fire or electric shock.
longer and lying hairs easily.components
It is recommended that you replace
Using the trimmerthe system outer foil at least once aCaution � To prevent
(see fig. 6)year and the inner blade at least onceHow to remove the built-in
personal injury or damage
Slide the trimmer handle up to openevery 2 years to maintain your shav-rechargeable batteries before
the trimmer.erOs cutting performance.disposal of the shaverto the product,
Place the trimmer at a right angle to(see fig. 10)Y Do not charge the shaver where the
Replacing the system outer foil
your skin and move it downward toThe batteries in this shaver are nottemperature is below 0°C (32°F) or
(see fig. 8)
trim sideburns.intended to be replaced by consum-above 40°C (104°F), where it will
Squeeze the system outer foil re-
ers. However, the batteries may bebe exposed to direct sunlight or a
lease buttons and lift the system
Cleaning your shaverreplaced at an authorized serviceheat source, or where there is a lot
outer foil upward to remove it. To in-
(see fig. 7)center. The procedure described be-of moisture.
sert the new system outer foil, press
low is intended only for removal ofY Use only the included power cord
down until it snaps into place.
Warning � To prevent electricthe rechargeable batteries for theRE7-05 to charge the ES8016/
shock or personal injury, discon-Replacing the inner bladespurpose of proper disposal.
ES8017/ES8018/ES8019 shaver.
nect the power cord from the(see fig. 9)Always make sure that the batteriesY Dry the shaver completely before
shaver and turn the shaver off be-Squeeze the foil frame release but-have been removed from the shaver
charging it.
fore cleaning.tons and lift the foil frame upward tobefore disposing of it.Y Keep the power cord away from wa-
remove it. Remove the inner blade,1. Disconnect the power cord from
ter and handle it only with dry
For cleanliness and convenience, we
one at a time, by grasping them firmlythe AC outlet, and remove thehands.
recommend that you clean your
at both ends and pulling straightpower cord from the shaver.
Y Grip the plug when disconnecting
shaver with water and a liquid hand
away from the shaver. To insert the2. Remove the outer foil frame andthe power cord from an AC outlet;
soap. Regular cleaning will keep your
new inner blade, hold the blade, onethe inner blades.
tugging on the power cord may
shaver in good condition while pre-
at a time, at both ends and press3. Remove the trimmer driving bardamage it.
venting odors or bacteria from devel-
downward until it snaps into the(a), slit blade driving bar (b) and
Y Store the power cord in a dry area
oping, and maintain the cutting per-
shaver.two screws (c).where it will be protected from dam-
formance.
4. Remove the four screw covers (d)age.
With the system outer foil in place,
(using something like a tooth-Y Do not pull, twist, or severely bend
apply some hand soap onto the outer
the power cord.
foil.
89
89 |
ACEC
