&:? 64"
�?´&:? 64"
�?´
B428077_EY7206_USA_Tori5 07-03-29 15:56:30
3WITCHAND&ORWARD2EVERSELED light How to use the belt hook To change the belt hook
LEVER/PERATIONCAUTION:WARNING:location side
The built-in LED light is designed to illu-� Be sure to attach the belt hookThe belt hook can be attached to either
minate the small work area temporarily. securely to the main unit with the screwside of the unit.
Do not use it as a substitute for a regularfirmly fastened. When the belt hook is
flashlight, since it does not have enoughnot firmly attached to the main unit, the
brightness.hook may depart and the main unit
may fall.
ForwardReverseThis may result in an accident or injury.
Depress the trigger switch, then LED light
turns on. When the trigger switch is
� Be sure to attach the belt hook firmly
released, the light turns off automatically.
and securely onto a waist belt or other
belt. Pay attention to the unit not
The light illuminates with very low current,1. Set the belt hook at storing position.
slipping off from the belt.
and it does not adversely affect the perfor-
This may result in an accident or injury.2. Loosen the screw turning it counter-
mance of the driver during use or its bat-
clock-wise, using a coin or a flat blade
Switch locktery capacity.� When the main unit is held by the beltscrew driver
hook, avoid jumping or running with it.
CAUTION:Doing so may cause the hook to slip
To prevent damage, do not operateand the main unit may fall.
Forward/Reverse lever until the bitThis may result in an accident or injury.
comes to a complete stop.
� When the belt hook is not used, be
sure to return it to the storing position.
&ORWARD 2OTATION 3WITCH
The belt hook may catch on something.
/PERATION
This may result in an accident or injury.
3XVKWKHOHYHUIRUIRUZDUGURWDWLRQ
� When the unit is hooked onto the waist
'HSUHVVWKHWULJJHUVZLWFKVOLJKWO\WRbelt by the belt hook, do not attach3. Take out the belt hook and insert into
VWDUWWKHWRROVORZO\driver bits to the unit. the other side of the slot on the main
A sharp edge object, such as a drill bit,unit
7KHVSHHGLQFUHDVHVZLWKWKHDPRXQW
may cause injury or an accident.
RIGHSUHVVLRQRIWKHWULJJHUIRUHIILFLHQW4. Fasten the screw firmly, turning it clock-
wise
WLJKWHQLQJRIVFUHZV7KHEUDNHRSHU
DWHVDQGWKHELWVWRSVLPPHGLDWHO\To set the belt hook angle
The belt hook can be taken out from the
ZKHQWKHWULJJHULVUHOHDVHGposition
main unit only when it is at storing position.
$IWHUXVHVHWWKHOHYHUWRLWVFHQWHUSR1. Slide the belt hook lock lever # and
VLWLRQ VZLWFKORFN hold it to unlock the belt hook.
2. Pull the belt hook from
2EVERSE 2OTATION 3WITCH$#
storing position $ and
/PERATIONset it as desired angle.
3XVKWKHOHYHUIRUUHYHUVHURWDWLRQ&KHFN3. Release the belt hook%
WKHGLUHFWLRQRIURWDWLRQEHIRUHXVHlock lever to lock the
'HSUHVVWKHWULJJHUVZLWFKVOLJKWO\WRangle of belt hook.
VWDUWWKHWRROVORZO\4. Make sure the belt hook is firmly locked
$IWHUXVHVHWWKHOHYHUWRLWVFHQWHUSR%. Also make sure the belt hook is firmly
locked into position.
VLWLRQ VZLWFKORFN
� The belt hook cannot
CAUTIONbe locked in this posi-
To eliminate excessive temperaturetion. Firmly lock it into
increase of the tool surface, do not oper-position before use.
ate the tool continuously (using two orTo return the belt hook to the storing
more battery packs consecutively.) Toolposition, Follow step 1. and 2. above, then
needs cool off time before switching tolower the belt hook.
another pack.To secure the lock, follow 3 and 4 above.
� 8 �� 9 �
Refine_EY7206_USA.8.p1.pdfRefine_EY7206_USA.9.p1.pdf
Refine_07-03-27 19:59:10Refine_07-03-27 19:59:09 |
ACEC
