Prior to using for the first time
Before using your dishwasher for the first time:b) Setting electronically
(The dishwasher must be switched off)
1.Ensure that the electrical and water connections comply
with the installation instructions
The dishwasher is factory set at level 5.
2.Remove all packaging from inside the appliance
1.Keep the start/cancelbutton pressed and turn the
3.Set the water softener
programme selector dial clockwise until the programme
4.Pour 1 litre of water inside the salt container and then fill
selection marker corresponds with the first washing
with dishwasher salt
programme.
5.Fill the rinse aid dispenserThe On/Off and start/cancelindicator lights start to flash
indicating that you have activated the water softener setting
Note:function.
If you want to use the "3 in 1" combi detergents, carefullyAt the same time, the end of programme indicator light
read the information given in "Different kinds ofstarts flashing.
detergents".The current level is indicated by the number of flashes of
the end of programme indicator light and a pause of about
5 seconds (see chart).
The water softener
Example:5 flashes + pause + 5 flashes etc...= level 5
The dishwasher is equipped with a water softener designed to
remove minerals and salts from the water supply, which would
2.To change the level, press the start/cancel button.
have a detrimental or adverse effect on the operation of the
Each time this button is pressed the level changes. (For the
appliance.
selection of the new level, see chart).
The higher the content of these minerals and salts, the harder
Examples:
your water is.
If current level is 5, by pressing the start/cancelbutton
Water hardness is measured in equivalent scales, German
once, level 6 is selected.
degrees (dH!), French degrees (TH!) and mmol/l (millimol per
litre - international unit for the hardness of water).If current level is 10, by pressing the start/cancelbutton
once, level 1 is selected.
The softener should be adjusted according to the hardness of
the water in your area. Your local Water Authority can adviseThe end of programmeindicator light remains off for about
you on the hardness of the water in your area.5 seconds and then starts flashing indicating the new set
made.
The water softener must be set in both ways: manually, using
the water hardness dial and electronically, using the
programme selector dial and the start/cancelbutton.3.To memorise the operation, switch off the machine by
returning the programme selector dial to the Off position,
that is the programme selection marker corresponds with
a) Setting manually
the On/Off indicator light.
1. Open the dishwasher door.Otherwise wait for about 60 seconds, after which the
2. Remove the lower basket from the dishwasher.dishwasher will automatically return to setting mode.
3. Turn the water hardness
dial to position 1 or 2 (see
table).
4. Replace the lower
basket.
The dishwasher is factory set
at position 2.
Water hardnessAdjustment of the Number of flashes of theUse
water hardness setting"end of programme" of
!dH!THmmol/lindicator lightsalt
manuallyelectronically
51 - 7091 - 1259,0 - 12,52level 1010yes
43 - 5076 - 907,6 - 8,92level 99yes
37 - 4265 - 756,5 - 7,52level 88yes
29 - 3651 - 645,1 - 6,42level 77yes
23 - 2840 - 504,0 - 5,02level 66yes
19 - 2233 - 393,3 - 3,92level 55yes
15 - 1826 - 322,6 - 3,21level 44yes
11 - 1419 - 251,9 - 2,51level 33yes
4 - 107 - 180,7 - 1,81level 22yes
< 4< 7< 0,71level 11no
25 |
ACEC
