ANTENNA CONNECTIONCABLE BOX CONNECTIONS
f you have a Cable Box, follow either set
combination antenna receives normal
Abroadcast channels (VHF 2?13 and UHF 14?69). Iof these steps to complete your The Cable TV signal omfrthe Cable Company
Your connection is easy because there is only one 75 connections.ý
ýý
(ohm) antenna jack on the back of your TV, and that?s
Cable Box with RF In/Out JacksOUTPUTCH
where the antenna goes.
This connection will nSotte rseuop psloyu nd CABLETO TV3 4
IN
Outdoor or Indoor Antennato the LCD TV.
(Combination VHF/UHF)
If your antenna has a round cableConnect the Cable TV signal to the IN jack (or
1(75 ohm) on the end, then you?re ready to 1RF IN or CABLE IN) on the Cable Box.75Coaxialý
connect it to the LCD TV. If your Connect an RF coaxial cable (not supplied) to Cableý
antenna has �at, twin-lead wire (300 ohm), you L-Adapter
Rear Jack panel of2the OUT jack (or TO TV or RF OUT) of the
�rst need to attach the Television
Cable Box.
antenna wires to the screws on a 300- to Side Jack Panel ofTelevision
Connect the other end of the coaxial cable to
ý
75-ohm adapter(not supplied).
ý3one end of the supplied L-Adapter as shown,
Twin-lead
wire toand connect the other end of the adapter to
Connect the antenna (or adapter) to one 300-75endý
the TV jack on the LCD TV.
2of the supplied L-Adapter as s-hown, and adacopternORPlug the DC adapter into the DC IN 16VVGAPC
nect the other end of the Antenna
with 75ý4jack on the LCD TV. Plug the power cýable into
L-Adapter to the TV jack on the side of cable
L-Adapteran outlet.
the LCD TV.
Set the Channel 3/4 (or Output channel) sDC Adawpteritch
5of the Cable Box to 3 or 4. Set the TV to the
same channel. When watching TV Power
Cable
programming, change channels at the Cable
Box, not the LCD TV.
Cable Box with Audio/Video Out Jacks
BASIC CABLE TV CONNECTIONThis connection wilSlt esruepop lsyo und to
the LCD TV.
Connect the Cable TV signal to the
our Cable TV signal into your home may be a 1IN jack (or RF IN or CABLE IN) on the Cable
Ysingle, 75(ohm) cable. If so, this connection is Box.
very simple. Follow the step below to connect your S - VIDEO
Cable TV signal to your new LCD TV.The Cable TV signal fromUsing an RCA-type video cable (not AUDIO
Cable Company
(75ý coaxial cable)2supplied) connect one end of the video cable to VIDEO
the Video Out jack of the Cable Box.Connect Side Jack Panel
Connect the Cable TV signal to one end of the the other end of the cable to the yellow VIDEO of Television
1supplied L-Adapter as shown, and connect the jack on the side of the TV.Video cables are
ý
other end of the adapter to the TV jack on the usually marked with yellow and are available
ý
LCD TV. from Magnavox or electronics retailers. Video
L-Adapter
jacks on most equipment are yellow.VGA
PCVideo Cable
Rear Jack panel ofUsing RCA-type, stereo audio cableýs (not
Television
3supplied), connect one end of the cables to the ý
left and right Audio Out jacks of the CDC aAdabpterle Box.
Connect the other end of that cable to the Audio Cable
Audio jack on the side of the LCD TV.AudPowiero
Cable
cables are usually marked with red and white Cable
TV signal
and are available from Magnavox or electronics
retailers.The right
audio jack is red and the left audio jack is white.
OUTPUT
Match the cable colors to the jack colors.CH
ý3 4
CABLETOL AUDIO RVIDEO
INTVOUTOUT
Plug the DC adapter into the DC IN 16V
Cable Box
4jack on the LCD TV. Plug the power cable into
an outlet.
89 |
ACEC
