PHILIPS 42FD9953/69S Instruction Manual

1015.5 en 12-11-2003 11:12 Pagina 7
Connect Peripheral Equipment
You may connect 3 possible VGA sources (VGA1,VGA2 or DVI-D) and
3 possible video sources (AV1,AV2 and AV3) to the monitor.
The following diagrams show you where you can connect your peripheral
equipment.
Note:in case the monitor is operating in combination with an electronic receiver box,
the AV inputs on the monitor will be disabled and the VGA2 connector becomes an
output.
Equipment with Y/C-SVHS output connectors
AV2
CVBSB/Pb/CbH
LLL
VGA 1VGA 2RC-OUT
RRR
RS232DVI-DVGA 2VGA 1DVI-DY/C S-VHSAUDIO IN AUDIO IN G/Y/YR/Pr/CrVAUDIO IN
~ MAINSAUDIOAV2AV1AV3
MAINS INLETLLLVGA 1VGA 2RC OUTAV 2LLCVBS PbHL
RS232Y/C&Connect the video cable to the AV2connector.
DVI-DRVGA 2RVGA 1RDVI-DRRYPrVR
éConnect the audio cables to the equipmentOs AUDIO Land Rsockets and to
the AUDIO L and AUDIO R AV2 sockets on the monitor.
Equipment with CVBS output connectors
AV1
CVBSB/Pb/CbH
LLL
VGA 1VGA 2RC-OUT
RRR
RS232DVI-DVGA 2VGA 1DVI-DY/C S-VHSAUDIO IN AUDIO IN G/Y/YR/Pr/CrVAUDIO IN
~ MAINSAUDIOAV2AV1AV3
&Connect the video cable to the AV1connector.
éConnect the audio cables to the equipmentOs AUDIO Land Rsockets and to
the AUDIO L andR AV1 sockets on the monitor.
Equipment with Component Video Output connectors
AV3
CVBSB/Pb/CbH
LLL
VGA 1VGA 2RC-OUT
RRR
RS232DVI-DVGA 2VGA 1DVI-DY/C S-VHSAUDIO IN AUDIO IN G/Y/YR/Pr/CrVAUDIO IN
~ MAINSAUDIOAV2AV1AV3
Note:AV3 can handle the following video signals:YCbCr,HD-YPbPr and HD-RGB.
The discrimination between the various input formats and the appropriate video
processing is done automatically.It is however possible to overrule the automatic
detection.See Setup menu,p.6.
&Connect the video cables of your equipment with YPbPr output with
composite sync on Y, or of your equipment with YCbCr output with
composite sync on Y to the YPbPr, resp.YCbCr input AV3 IN sockets of the
monitor.
éConnect the video cables of your equipment with RGB output with separate
Horizontal and Vertical sync to the RGB input sockets and to the H and V
sockets AV3 of the monitor.
ŤConnect the audio cables to the equipmentOs AUDIO Land Rsockets and to
the AUDIO IN L and AUDIO IN R AV3 sockets on the monitor.
Note:when High Definition signals are inputted to the monitor via the YCbCr/RGB
input,the monitor switches to the HD Video Mode.
The following HD and ED video modes are supported by the monitor on the YCbCr,
RGB and VGA2 HD input:
1920x1080/60I720x480/60P
1280x720/60P720x576/50P
The following SD video modes are supported by the monitor on theYPbPr input:
720x480/60I
720x576/50I
Note:you should make the correct selection for AV3 in the Setup menu,p.6.
7