Connecting Accessory Devices to Your TV
CONNECTINGA VCR
he TVOs audio/video (AV) input jacks provide
Tfor direct picture and sound connectionsBack of TV
ANTENNA IN 75&
between the TVand accessory devices such as
2
VCRs, DVD players, and others that have AVout-
put jacks.
HD INPUT-AV 5
This example, which uses the INPUT-AV1 jacks,
DVI
shows you one way you can connect a VCR to
HD INPUT-AV 4
your TV.
G/Y
3
Refer to the directions-for-use manual for yourR/Pr
INPUT-AV 1OUTPUTINPUT-AV 2
4
VCR for further information on connections.Y
B/Pb
VIDEOVIDEO
S-VIDEOTo make the connections shown in this example,LPbS-VIDEOLV
LLLL
you will need:AUDIOPrAUDIOSYNCAUDIOAUDIOCable TV
H
RRRR
Y one coaxial cable (75&)Signal
Y one cable for a video connection (standard
RCA-type phono plug)
1
Y two cables for audio connections (standard
RCA-type phono plugs) (only one cable isAUDIO
LANTIN
needed for a nonstereo VCR).OUTIN
R
NOTE:The cables are not supplied with your TV.VIDEO
OUT
You should be able to buy them at most storesOUTINCH3CH4
that sell electronics. Or you can call our
Customer Care Center at 1-800-531-0039Back of VCR
(example only)
Connect a cable TV or antenna signal
HELPFUL HINT
to the ANT IN jack on the back of theAV2
1
VCR.Y Stereo sound will pass from the ANT
OUT jack on the VCR to the ANTENNA
Connect from the OUTojackn theIN 75& jack on the TV only when the
back of the VCR to the ANTENNA INVCR is in TV mode. This is the mode
2
75& jack on the back of the TV.that allows the TV to use its channel
selector.
Connect the VIDEO OUT jack on the
back of the VCR to the INPUT-AV 2Y To simplify making connections, audio
3
VIDEO jack on the back of the .TVand video cables often have color-coded
plugs. The jacks on your TV are likewise
Connect the audio output R(ight) andPOWERcolor coded to match the plugs. The cod-
L(eft) jacks on the back of the VCR toing is as follows:
4
the INPUT-AV 2 AUDIO jacks on the
NYellow for video (composite)
back of the TV.
NRed for the right audio channel
TVVCRACC
NOTE: If the VCR is a mono (nonstereo)ACTIVENWhite for the left audio channel
SWAPPIP CHCONTROL FREEZE
unit, connect only the left audio cable,DNUP
NOTE: If your VCR is mono (non-
which usually has a white-coded plug.SOUNDPICTURE
stereo), you will connect only one audio
cable. You must ensure that the TV is set
Press the AV button on the remote con-
STATUS/MENU/SELECTto MONO for the signal source to which
trol as many times as necessary to selectEXIT
5youOve connected the INPUTVCR (-AV 2,
the AV2 source for viewing of materials
from the VCR.MUTEINPUT-AV 1, or the side panel inputs
VOLCH[AV3]). Otherwise, you will receive
sound from only one of the TVOs speakers.
See page 36.
213
546
cc CHECK IT OUT
798
TV/VCR
A/CH0SURFYou can display the AV1, AV2, or AV3 signal
sources in the PIP window. See page 7 of the
5SURFPIP ON/OFFREC YFORMATSLEEPQuick Use and Setup Guidefor information on
SAP
AVDOLBY V PROG.LISTusing the Picture-in-Picture (PIP) feature.
ITR/HOMEHOME PERSONAL
9 |
ACEC
