EnglishControls/Power SupplyPower SupplyGeneral operation/Radio
Y Incorrect use of batteries can cause General operation
Supplied accessoriesBack panel
AC mains leadelectrolyte leakage and will corrode the 1 To select your sound source adjust the
# Telescopic antenna - improves FM compartment or cause the batteries to burst:
source selector to : CD, TUNER or
reception.Y Do not mix battery types: e.g. alkaline withTAPE/POWEROFF.
Top and front panels (See 1)carbon zinc. Only use batteries of the same
$ Battery door - open to insert 6 x 1.5V 2 Adjust the sound with the VOLUME
1 VOLUME � adjusts volume levelR-14/ UM2/ C-cells.type for the set.
control.
% AC MAINS - inlet for power cordY When inserting new batteries, do not try to
2 Source selector : CD, TUNER,3 To switch off the set, adjust the source selec-
mix old batteries with the new ones.
TAPE/POWEROFFCAUTIONtor to TAPE/POWEROFF position and check
� selects CD, tuner or tape source of soundY Remove the batteries if the set is not to bethe cassette keys are released.
Use of controls or adjustments orused for a long time.
� power off switchperformance of procedures other
3 CD doorthan herein may result in hazardousUsing AC MainsRadio reception
radiation exposure or other unsafe1 Check if the power/mains voltage, as shown1 Adjust the source selector to TUNER.
4 TUNING � tunes to radio stations
operation.on the type plate located on the 2 Adjust BAND to select your desired
5 BAND � selects waveband
bottom of the set, corresponds to yourwaveband, FM or AM.
6 PREVIOUS, NEXT , §Power Supplylocal power supply. If it does not, consult your
3 Turn TUNING to tune to a station.
� skips or searches a passage/track Whenever convenient, use the mains supplydealer or service center.
backwards or forwardcord if you want to conserve battery life.2 Connect the power cord to the ACY For FM, extend and turn the telescopic
antenna for best reception. Reduce its length
7 PROG � programs and reviews Make sure you remove the plug from the setPOWER/MAINS inlet and the wall socket.if the signal is too strong.
and wall outlet before inserting batteries.
programmed track numbersThe mains lead is now connected and ready
for use.Y For AM, the set uses a built-in antenna.
8 Cassette recorder keys:Batteries (not included)Direct this antenna for best reception by
1 Open the battery compartment and insert3 To switch the set off completely, withdraw theturning the whole set.
; � pauses playback or recordingpower cord from the wall socket.
six batteries, type R-14, UM-2 or C-cells,
9/ � stops the tape;(preferably alkaline) with the correct polarityY Disconnect the mains lead from the wall4 To switch off the radio, adjust the source
selector to TAPE/POWEROFF position and
� opens the cassette holderas indicated by the "+" and "�" symbols insidesocket to protect your set during heavy
check the cassette keys are released.
5 or 6 � fast winds/ rewinds tapethe compartment. (See 1)thunderstorms.
2 Replace the compartment door, making sure
1 � starts playback
the batteries are firmly and correctly in place.Helpful hints :To avoid unnecessary energy
0 � starts recording
The set is now ready to operate.consumption, always adjust the source
9 Cassette doorselector to TAPE/POWEROFF after using
Batteries contain chemical substances,sothe set.Also check that the tape deck keys
0 CD Display � shows the CD functionsthey should be disposed of properly.
are released
! PLAY/PAUSE 2; - starts or pauses CD
playback.The type plate is located on the bottom
of the set.
@ STOP 9 � stop playback;
� erases a CD program. |
ACEC
