#@!0987654321EnglishControls/Power Supply
before plugging in the set adjust to match the local voltage 110/220V VACwhen headphones are connected to the set. Helpful hints: pBattery door TBack/bottom panels (VTUNINGOPENYCLOSESHUFFLEREPEATDisplay9PROG � fast searches forwards/backwards � 2; �� Source selectorT� AC power cord Supplied Accessories
oltage selector elescopic antennaOLUME(press and hold the button) selects the next/previous track power off switch sound selects CD or radio (FM/MW) source ofop/front panels
� � �
3.5 mm stereo headphone socketerases a CD program stops CD playback;�
MAINS~
starts or pauses CD playback
�� programs tracks and reviews the
�shows the CD functions program
�� tunes to radio stations � CD program/entire CD. repeats a track/
adjusts volume level
plays all tracks in random order
� inlet for power cord The speakers will be muted� open to insert 6 x 1.5V
R-14� opens/ closes the CD:CD
� (not for all versions)door
/ � improves FM ,
UM-2reception FM
(See
,
MW or OFF
/
C-cells1
See
)
1
)
Y Remove the batteries if the set is not to beY When inserting new batteries,do not try to mixY Do not mix battery types:e.g.alkaline with car-Y Incorrect use of batteries can cause 2 1
they should be disposed of properly. Batteries contain chemical substances,soused for a long time.old batteries with the new ones.for the set. bon zinc.Only use batteries of the same typecompartment or cause the batteries to burst electrolyte leakage and will corrode the is now ready to operate. teries are firmly and correctly in place.The set Replace the battery door,making sure the bat-partment by alkaline) with the correct polarity as indicated type Open the battery door and insert 6 batteries,Batteries (not included)and wall outlet before inserting batteries. Make sure you remove the plug from the set cord if you want to conserve battery life. Whenever convenient,use the power supplyPooperation. than herein may result in unsafe performance of procedures other Use of controls or adjustments orCA
the "
w
R-14UTION
er Supply
+
(See ," and "
UM-2
1 �
). " symbols inside the com-
or
C-cells
,(preferably
:
�Y54 3 2 1 Po
after using the set. always adjust the To Helpful hints:bottom of the set. The type plate is located on the thunderstorms. socket to protect your set during heavy Disconnect the power cord from the wallthe AC power plug can be easily reached. Install the unit near the AC outlet and wherethe power cord from the wall socket. Toset is now connected and ready for use. AC Connect the power cord to the with the local power supply. tor,adjust the selector so that it matches If your set is equipped with a voltage selec-dealer or service center. local power supply.If it does not,consult your bottom of the set, the type plate located on the Check if the power voltage,you change or disconnect power supply. completely switched off the set,before W Using AC powerw
avoid unnecessary energy consumption, ARNING:Always check you have switch the set off completely,withdraw
er SupplyGeneral Operation/Tuner
MAINS~
inlet and the wall socket.The
Source selector
corresponds to your
as shown on
to
OFF
YY21 2 1
turning the whole set. Direct this antenna for best reception by For length if the signal is too strong. ic antenna for best reception.Reduce its For ToHelpful hints:Turn MW Adjust the Radio reception Adjust the sound with the Adjusting volume Source selector ToSource selector To function Switching on and off and selecting theG
improve radio reception switch off the set,adjust the select your sound source,adjust theeneral operation
MWFM
TUNINGto select your desiredwaveband.
,
,extend,incline and turn the telescop-
the set uses a built-in antenna.
Source selector
to tune to a station.
to to:
OFFCD
V,
OLUMEposition.FM
to
or
FM
MW.
orcontrol. |
ACEC
