NAMES AND FUNCTIONS OF PARTS
26 Microphone equalizer control dial (EQ)
Beat effect section
Use to adjust the tone of microphones 1 and 2. When rotated fully
15 BPM displayclockwise, attenuation of low-range sound is maximized. When
rotated fully counterclockwise, attenuation of high-range sound is
Displays the current track tempo as Beats Per Minute (BPM).
? The display flashes during BPM calculation and when BPM cannotmaximized. (Adjustable range 0 dB to �12 dB)
be calculated.27 Microphone function selector switch (MIC)
OFF:
16 BPM measuring mode button/indicator (AUTO)
No microphone sound is output.
Each time the button is pressed, the BPM measuring mode alternatesEnglishON:
as follows:
Microphone sound is output normally.
AUTO mode:
The AUTO button lights and the BPM is calculated automatically.TALK OVER:
Microphone sound is output; when sound is input to a connected
This is the default mode whenever power is first turned on.
TAP mode (manual input):microphone, the TALK OVER function operates and all sound other
than that from the microphone is attenuated by 20 dB.
The AUTO button does not light, and BPM is input manually by using
the TAP button.
17 TAP buttonHeadphones output section
The BPM is calculated from the intervals at which the TAP button is
28 Headphone cue button/indicator
struck. If the TAP button is tapped in the AUTO mode, the mode(CH-1, CH-2, MASTER)
automatically switches to the TAP mode (manual input).
Press the button for the source you wish to monitor with
18 Beat select buttons (BEAT/PITCH �, +)
headphones. When a button is OFF, its indicator lights dimly; when
+ (Beat up):Doubles the calculated BPM.ON, the button indicator lights brightly (P. 8).
� (Beat down): Halves the calculated BPM.When the [ECHO] effect is selected, the effect is not applied to
? If one of the BEAT/PITCH buttons (�, +) is pressed while holdingheadphone outputs if headphone cue button CH-1 or CH-2 are set to
the TAP button depressed, the BPM can be changed (40 to 999, inON.
1-step increments).
During in-loop sampler play, the loop play speed is changed.29 Headphones level adjust dial (LEVEL)
Adjusts the output level of the headphones jack. (Adjustable range:
+ (Beat up):Play speed becomes faster while button is pressed.
� to 0 dB).
� (Beat down): Play speed becomes slower while button is pressed.
30 Headphones jack (PHONES)
19 Beat select/bank buttons/indicators
(BEAT 1 (1/2), 2 (3/4), 4 (1/1), 8 (2/1), 16 (4/1) /Located on the unitOs front panel.
BANK)
Use to select the beat for synchronizing effects (P.11)
The selected button lights.
During in-loop sampler play, the buttons function as bank buttons to
record samples of the music (P. 12).
? If the BEAT/BANK button is pressed while holding the ERASE
(BEAT/PITCH �) button depressed, the music sample recorded in the
BEAT/BANK button will be erased.
20 Effect selector (DELAY/ECHO/FILTER/FLANGER/
PHASER/ROBOT/ROLL/IN-LOOP SAMPLER)
Use to select desired type of effect (P. 10 to 12).
21 Effect channel selector
(CH. SELECT 1/2/MIC/MASTER)
Use to select the channel to which beat effects are applied (P. 11).
When [MIC] is selected, effects are applied to both microphone 1 and
microphone 2.
22 Effect parameter dial (LEVEL/DEPTH)
Adjusts the quantitative parameters for selected beat effect (P. 11 to
12)
23 Effect button/indicator (ON/OFF)
Sets selected beat effects ON/OFF (P. 11).
When effects are disabled (OFF), the button lights. When effects are
enabled (ON), the button flashes. Whenever power is first turned ON,
effects default to OFF.
Microphone input control
24 Microphone 1 level control dial (MIC 1 LEVEL)
Use to adjust the volume of microphone 1. (Adjustable range � to 0
dB)
When the connection panelOs MIC/AUX switch is set to [AUX], this
dial adjusts the sound volume for the left channel (AUX(L)).
25 Microphone 2 level control dial (MIC 2 LEVEL)
Use to adjust the volume of microphone 2. (Adjustable range � to 0
dB)
When the connection panelOs MIC/AUX switch is set to [AUX], this
dial adjusts the sound volume for the right channel (AUX(R)).
7
<DRB1404>
En |
ACEC
