NAME AND FUNCTION OF PARTS
9 Monitor Monaural/Stereo Selector Switch^ Master Balance Knob (MASTER BALANCE)
(MONO/STEREO)Used to adjust the left and right balance of the master
output.
0 Monitor Equalizer Knob (MONITOR EQ)
& Booth Monitor Level Knob (BOOTH MONITOR
Used to obtain the beat easily with the headphone moni-
tor sound.LEVEL)
Increases/decreases low tone.Used to adjust the output level of the BOOTH MONITOR
Flat at center click.terminal.
Increases when rotated to the right. (To +12 dB at 100 Hz)Not affected by the master volume and master balance.
Decreases when rotated to the left. (To �12 dB at 100 Hz)
* Effect Selector Switch (EFFECT SELECTOR)
- Monitor Level Knob (MONITOR LEVEL)AUTO BPM (Beat/minute):
Used for adjusting the headphone monitor volume.Select when performing BPM detection.
Not affected by the master volume and master balance.DELAY:
Delays the time and repeats once.
= Headphone Terminal (PHONES)ECHO:
Delays the time and repeats several times to produce the
echo effects.
~ Channel Fader VolumeAUTO PAN:
Used for adjusting the volume of CH1 to CH4.Shifts the left and right channels periodically.
FLANGER:
Produces periodic sound change effects by mixing the
! Assign Switch (ASSIGN A, B)short delay sound and original sound.
When performing cross fader using two sources (A, B),
select the channels (CH1 to CH4) to be assigned to AREVERB:
Produces the reverb effects.
and B.PITCH SHIFTER:
Effective when the cross fader switch ($) is on (cross
Changes the pitch of the song.
fader mix).SEND/RETURN:
Select when connecting and using the external effector.
@ Fader Start Switch (FADER START) (Refer to
Page 17.)( Effect Channel Selector (CH. SELECTOR)
When the optional CD player (CDJ-500G or CDJ-500 )Use to select the source to be effected.
is connected to the unit using the control cord, this
ON/OFF switch is used to start automatic playing of
the CD player using the channel fader or cross fader.) Parameter Knob (PARAMETER)
Used to adjust the parameter of the effector selected with
the effect selector switch.
# Cross Fader Volume (CROSS FADER)DELAY:
Adjusts the mix volume of the sources set to A and B0 to 680 mSec (2 mSec step to 100, 5 mSec step from 100
using the assign switch (!).to 680)
ECHO:
0 to 680 mSec (2 mSec step to 100, 5 mSec step from 100
$ Cross Fader Switch (CROSS FADER ON/OFF)
OFF:to 680)
AUTO PAN:
Select when mixing sounds using the channel fader volume.0 to 3500 mSec (5 mSec to 100, 10 mSec from 100 to 900,
(Direct mix.)
ON:20 mSec step from 900 to 3500)
FLANGER:
Select when mixing sounds using the cross fader. (Cross100 to 9000 mSec (10 mSec to 900, 50 mSec from 900
fader mix.)
to 9000)
REVERB:
% Master Volume Level Adjustment0 to 100% (1% step)
Used to adjust the level of the master output volume.PITCH SHIFTER:
When the cross fader is ON, the sounds of assigns A, B0 to ?100% (1% from 0 to 10, 2% step from 10 to 100)
and main microphone will be output.
When the cross fader is OFF, the sounds of each channel_ Effect Switch (EFFECT ON/OFF)
and main microphone will be output.Use to switch the effect on/off.
When turned on according to the beat, the effects will
also correspond to the beat.
When the effect is on, it goes on and off.
10
<DRB1192> |
ACEC
