Settings are canceled.
Troubleshooting
When the power is turned off by power failure or by
Incorrect operations are often mistaken for trouble andunplugging the power cord, settings will be canceled.
malfunctions. If you think that there is something wrong\ Before unplugging the power cord, press
with this component, check the points below. STANDBY/ON and check that O--OFF--�
Sometimes the trouble may lie in another component.disappears in the display.
Inspect the other components and electrical appliances
being used. If the trouble cannot be rectified even afterNo picture.
exercising the checks listed below, ask your nearestThe rear panelOs VIDEO OUT SELECT switch setting
PIONEER authorized service center or your dealer tois not correct.
carry out repair work.\ Check that the VIDEO OUT SELECT switch is set
to the correct position for the monitor connection
you are using (page 16).
The disc table comes back out automatically, shortly
Connection is incorrect.
after the disc table is closed.
The disc is dirty or warped.\ Check that cord connections are correct and that
plugs are firmly connected.
\ Refer to �Disc CareO (page 49).
Operation (settings) of TV or AV amplifier is not
The disc is not placed properly on the disc table.appropriate.
\ Use the disc table guide to align the disc (page 20).\ Be sure that your TV, receiver, or amplifier is set
Region number does not conform with this unit.up to view DVD playback.
\ If the region number on the disc does not match
the number on the player, the disc cannot be usedThe screen is stretched or aspect does not change.
(page 55).The multi aspect setting is not appropriate.
\ Change the aspect setting in the [TV Screen]
There is condensation on the operating section of thesetting in the Setup screen Video menu to the
player.
screen type most appropriate to the TV or monitor
\ Allow time for condensation to evaporate. If playeryou are using (page 28).
is near an air conditioning unit, you should move
the player (page 50).Picture disturbance during playback or dark.
This player is compatible with Macro-Vision System
Playback is not possible.
copy guard. Some discs include a copy prevention
The disc has been loaded upside down.signal, and when this type of disc is played back,
\ Check that the disc has been loaded with the labelstripes etc., may appear on some sections of the
side facing up.picture depending on the TV.
\ This is not a malfunction.
mark appears on screen.
The selected function does not operate for that disc.The TV system may be set inappropriately.
\ See OSetting the TV System� on page 17.
mark appears on screen.Discs respond differently to particular player functions
The operation is prohibited by the player.which may result in the screen becoming black for a
brief instant or shaking slightly when the function is
Picture playback stops and the operation buttonsexecuted.
cannot be used.\ These problems are largely due to differences
Player malfunctions.between discs and disc content and are not
\ Stop disc playback (press STOP 7), then startmalfunctions of this player.
playback again.
Audio is output from the analog output jacks but not
New settings made in the Setup screen menus whilefrom the digital output jacks.
a disc is playing are ineffective.Player settings are incorrect.
Some settings can be changed while a disc is playing,\ In the Audio 1 menu, check that the appropriate
but are not effective. This is not a malfunction.digital audio output formats are selected, and that
\ Make the same setting when the player isthe [Digital Out] setting is not set to [Off] (page
stopped.27).
\ Stop disc playback (press STOP 7), then startWhen recorded on a VCR or passed through an AV
playback again. When playback is resumed, the
selector, there is disturbance in the playback picture.
new settings should be in effect. Please note that
making settings in the Setup screen menus mayDue to the playerOs copy protection circuits,
connection of this device through a VCR or an AV
cancel the resume function.
selector may prevent recording or cause picture
problems.
When making changes in the Setup screen menus,
\ This is not a malfunction.
is displayed.
There is a Video CD or CD loaded in the player and the
setting that was changed only applies to DVD
performance.
\ The setting will be effective the next time a DVD
is loaded.
52
En |
ACEC
