DESCRIPTIONanchors supplied to the wall (in
correspondence to the holes B (Fig. 6). Insert
--------------------------------------------------------
two of the screws supplied and hook the
The appliance can be used both in Ductingapparatus using the holes B on the rear (Fig.6).
version and Filtering version.Before fully tightening the screws, mark the
In the Ducting version (Fig. 1), cookingposition of the 2 holes C on the wall with a
vapours and/or odours are conveyed straight
marking pen. Unhook the hood and drill the 2
outside (ceiling and/or wall) by a disposal duct,holes in the marked positions and insert the
using the holes that are predisposed on thescrew anchors. Hook the hood back on and
top and/or at the back of the apparatus.finally fix it with the 4 screws. Remove the
In the Filtering version (Fig. 2) cookingadhesive tape from the telescopic part and
vapours and/or odours are depurated by 2
pull it downwards until it touches the hob.
charcoal filters and recirculated around theMake the electrical connection.
room by the front fissures. ATTENTION: For
the filtering version it is absolutely necessaryAssembly of the telescopic flue (Fig. 7)
to use the charcoal filters whereas for the
Fix the lower bracket (D) onto the apparatus.
ducting version it is not.Fix the upper bracket (E) onto the ceiling; in
order to position the bracket on the same axis
INSTALLATIONas your apparatus, refer to the small triangle
--------------------------------------------------------(F) that is on the central axis.
Take the two telescopic pipes minding that
Before assembling the appliance it is necessary
you have to lift slightly the smaller pipe (the
to take off the anti-grease grilles. To take off theupper one); insert the pipes from the front,
grill it is necessary to push this one towards the
expanding slightly with your hands so that
rear of the apparatus, by means of the properthey can get hooked onto the two brackets.
knobs, so that it gets released, and to rotate it
Fix the pipes to the brackets by means of the
(Fig. 3); to take it off completely, make it rotatescrews G and H.
on one side keeping the other one steady.
For the ducting installation of the appliance,Wall cupboard fitting
connect one of the two discharge outlet toUsing the appropriate drilling jig make the four
the external ducting and seal the otherfixing holes into the bottom of the wall cupboard
opening with the supplied cap (Fig. 4). Forand cut the air venting hole if the hood is a ducting
the filtering installation you must close bothversion one (for the filtering version this hole is
the discharge outlets of the apparatus usingnot necessary). Holding the hood against the
the supplied caps.bottom of the cupboard fix it to it by means of the
supplied four screws (Fig. 8).
The following operations are essential forFig. 9: take 2 of the screws (S) enclosed (the
assembly:smallest ones) and partially insert them in the
- Install a proper wiring system.holes on the telescopic slide (A); do not fix
- If your apparatus is to be assembled as athem completely: they must hold the telescopic
Ducting appliance, you must first make theslide. Push the slide back as much as possible
air venting hole and get a proper pipe toand block it with some adhesive tape (W).
connect the hole to the flange of the hood.Rest the lower part of the hood against the
wall and mark the position of the 2 holes C
Wall fitting(Fig. 9) on the wall with a marking pen.
Fig. 5: take 2 of the screws (S) enclosed (theRemove the lower part and drill 2 holes in the
smallest ones) and partially insert them in themarked positions and insert the screw
holes on the telescopic slide (A); do not fixanchors.
them completely: they must hold the telescopicFix the lower part by means of the 6 screws
slide. Push the slide back as much as possiblesupplied (Fig. 9).
and block it with some adhesive tape (W).Remove the adhesive tape from the telescopic
Fix the lower part to the upper part of thepart and pull it downwards until it touches the
hood by means of the 4 screws supplied (Fig.hob.
5).Make the electrical connections.
Using the drilling template fit 2 of the screw |
ACEC
