Fantom-Xa_e.book 125 Z8 ???? ???e?? xý~
U xý9=?p? Â
Recording Songs
5.When you are finished recording, press [].Using Auto Punch-In Recording
The [] indicator will go dark.
You must pre-specify the area (punch points) in which recording is
to take place. This is convenient when you want to re-record over a
If you are not satisfied with the realtime recording you just mistake. The song will play back when you begin recording. When
made, you can press [ERASE/UNDO] to return to the state you reach the punch-in point, playback will switch to record mode.
prior to recording. After executing Undo, you can use Redo to
revert to the previous state. After executing Undo, you can 1.In the Realtime Rec Standby window, set the Loop/Punch
execute Redo by performing the above procedure once again.parameter to OAUTO PUNCH.�
2.Set the Start Point/End Point parameters to the desired
Recording Tempo Changes in a punch points.
Song (Tempo Recording)3.Move to a measure earlier than the specified Start Point,
and press [] or [F6 (START)].
If you want the tempo to change during the song, you can record
The song will begin playing. Recording will begin at the
those tempo changes in the Tempo track. If tempo changes have
location specified by the Start Point parameter. Playback will
already been recorded in the tempo track, they will be rewritten.
resume at the location specified by the End Point parameter.
Set the following recording parameters in addition to the basic
settings described in step 3 of p. 124.4.Press [] to stop playback.
ParameterValueExplanation
Using Manual Punch-In Recording
Tempo Rec SwOFF, Specify whether tempo changes will
ONbe recorded (ON), or not (OFF).Recording takes place (erasing the existing data) in the area that you
specify by pressing a pedal or button. This is convenient when you
You will be able to use REALTIME CONTROL knob want to re-record more than one location in which you made a
movements to control the tempo easily (p. 121).mistake. The song will play back when you begin recording. When
you press a pedal or button, playback will switch to record mode,
and will switch back to play mode when you press the pedal or
Loop Recording and Punch-In
button once again. By pressing the pedal or button, you can toggle
Recordingbetween record and play modes.
You can record repeatedly over a specified area (Loop recording), or
If you want to use a pedal connected to the PEDAL CONTROL
re-record just that area (Punch-in recording).
jack to specify the area for recording, you must first set the
Set the following recording parameters in addition to the basic
Control Pedal Assign parameter to OPUNCH IN/OUT� (p. 195).
settings described in step 3 of p. 124.
1.In the Realtime Rec Standby window, set the Loop/Punch
ParameterExplanationparameter to OMANUAL PUNCH.�
Loop/Specify how loop recording or punch-in recording
Punchis to take place.2.Press [] or [F6 (START)].
OFF: Song playback will begin, and the Realtime Rec Control
Loop recording or punch-in recording will not oc-window will appear.
cur.fig.PunchIn1
LOOP (POINT):
Recording takes place repeatedly, according to the
loop point settings.
LOOP (1�16 MEAS):
The 1�16 measure area starting at the record-start
measure will be recorded repeatedly.
LOOP SONG ALL: 3.At the point where you want to begin recording, press [F3
The entire song from beginning to end will be re-(PUNCH IN)] or step on the pedal.
corded repeatedly.Playback will switch to record mode.
AUTO PUNCH: fig.PunchIn2
Auto punch-in recording will be performed.
MANUAL PUNCH:
Manual punch-in recording will be performed.
Start PointMeasure and beat at which loop recording or auto
punch-in recording is to begin
* It is not possible to specify the Tick.
4.At the point where you want to stop recording, once again
End PointMeasure and beat at which loop recording or auto
press [F3 (PUNCH OUT)] or step on the pedal.
punch-in recording is to Stop.
You will return to playback mode.
* It is not possible to specify the Tick.
* The minimum loop length is four quarter notes.5.Press [] to stop playback.
125 |
ACEC
