AVD-C700ES
2-1. Disc Type2-1-3.Disc Type CD
It sets up so that it may judge as a disc type of specification of the
Disc Typedisc with which the set was inserted.
[1]: CD disc (normal speed, 12 cm)
Disc Type Select[2]: CD disc (double speed, 12 cm)
[3]: CD disc (normal speed, 8 cm)
1. Disc Type Auto Check[4]: CD disc (double speed, 8 cm)
2. Set Disc Type DVD[5]: CD-RW disc (normal speed, 12 cm)
3. Set Disc Type CD[6]: CD-RW disc (double speed, 12 cm)
4. Set Disc Type Hybrid[7]: CD-RW disc (normal speed, 8 cm)
[8]: CD-RW disc (double speed, 8 cm)
2-1-4.Disc Type Hybrid
It sets up so that it may judge as a disc type of specification of the
Exit: RETURNdisc with which the set was inserted.
[1]: SACD Hybrid disc (SACD layer, 12 cm)
[2]: SACD Hybrid disc (CD layer, normal speed, 12 cm)
2-1-1.Disc Type Auto Check[3]: SACD Hybrid disc (CD layer, double speed, 12 cm)
1) Press the [1] key on the remote commander to display the Disc[4]: SACD Hybrid disc (SACD layer, 8 cm)
Type Auto Check screen.[5]: SACD Hybrid disc (CD layer, normal speed, 8 cm)
2) Insert a disc and press the [ENTER] key on the remote[6]: SACD Hybrid disc (CD layer, double speed, 8 cm)
commander.
3) It judges the type of inserted disc automatically and displays2-2. Servo Control
the disc type and so on as below.Note: Be sure to perform the disc type setup before performing this item.
Disc Type Auto CheckServo Control
1.LDoff R.Sled FWD
Disc Typexx 2.Focusoff L.Sled REV
Layerxx 3.SPDLoff U.Sled Reset
Mirr Timexx 4.CLVAoff D.Sled Limit
Mirr Countxx 5.Trk.off
FZC Countxx 6.Sledoff
PI Referencexx 7.Fcs.Srchoff
PI Peakxx
ENTER.Execute 0.All Servo Off
Exit: RETURNExit: RETURN
Disc Type : CD, DVD or Hybrid (SACD)On this screen, the servo on/off control necessary for replay is
Layer: SINGLE, DUAL or HYBRIDexecuted. Normally, turn on each servo from 1 sequentially and
Mirr Time :Mirror time of between disc surface and recordwhen CLVA is turned on, the usual trace mode becomes active. In
surface when disc type judgment. (hexadecimalthe trace mode, DVD sector address or CD time code is displayed.
number)This is not displayed where the spindle is not locked.
Mirr Count : The number of times which mirror counts betweenThe spindle could run overriding the control if the spindle system is
disc surface and record surface when disc typefaulty or RF is not present. In such a case, do not operate CLVA.
judging.
FZC Count : The number of times which focus zero cross points[1] LD: Turn on/off the laser.
of each layer when lens down.[2] Focus: Search the focus and turn on the focus.
PI Reference: The average of PI reference voltage. (he[3] SPDLxadecimal: Turn on/off the spindle.
number)[4] CLVA: Turn on/off normal servo of spindle servo.
PI Peak: PI peak level voltage. It performs only w[5] Trhen disck.: Turn on/off the tracking servo.
type judgment is successful. (hexadecimal n[6]umber) Sled: Turn on/off the sled servo.
[7] FCS. Srch:Turn on/off the focus search.
2-1-2.Disc Type DVD[10/0]:All servo off.
It sets up so that it may judge as a disc type of specif[R] Sled FWD (right cursor)ication of the: Move the sled forward.
disc with which the set was inserted.[L] Sled REV (left cursor):Move the sled reverse.
[1]: DVD single layer disc (12 cm)[U] Sled FWD (up cursor):Reset the sled.
[2]: DVD dual layer disc (0 layer, 12 cm)[D] Sled REV (down cursor):Limit in the sled.
[3]: DVD dual layer disc (1 layer, 12 cm)
[4]: DVD-RW disc (12 cm)
[5]: DVD single layer disc (8 cm)
[6]: DVD dual layer disc (0 layer, 8 cm)
[7]: DVD dual layer disc (1 layer, 8 cm)
[8]: DVD-RW disc (8 cm)
24 |
ACEC
