STATEMENTOFROHSCOMPLIANCE
This appliance has a serial number located on the rear panel. Please record the model number and serial
number and retain them for your records.
PMI Audio Group manufactures complete electronic products which are cov-
ered by the European Unions Removal of Hazardous Substances directive Model number
2002/95/EC (RoHS). This directive seeks to eliminate toxic substances from
the manufacturing process, such that when equipment is disposed of at the Serial number
end of its life cycle, the materials it contains do not contaminate the environ-
ment and pose health risks. Banned substances are lead, mercury, cadmium, NOTE ? This apparatus does not exceed the Class A/Class B (whichever is applicable) limits for radio noise
emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of
hexavalent chromium, polybrominated biphenyls (PBB) and polybrominated
Communications.
diphenyl ethers (PBDE). Lead is used together with tin in solder connections to
reduce the melting point of solder. Lead-free solder requires higher soldering ATTENTION ? Le présent appareil numérique n?émet pas de bruits radioélectriques dépassant las limites
temperatures which in turn places greater thermal stress on components.applicables aux appareils numériques de class A/de class B (selon le cas) prescrites dans le réglement sur le brouil-
lage radiolectrique dict par les ministere des communications du Canada.
PMI Audio Group takes seriously its obligations under the RoHS directive and insists that its
These limits are designed to provide reasonable protection against harmful interference in a commercial/residen-
factories use only components that are certied RoHS compliant, as well as leadfree solder. In a
tial installation respectively. This equipment generates, uses, and can radiate radio frequency energy and, if not
very few cases the necessary components may not yet be available to the world market but we
installed and used in accordance with the instruction manual, may cause harmful interference to radio commu-
work continuously to eliminate any such exceptions at the earliest opportunity. Our printed Circuit
nications. There is no guarantee that interference will not occur in a particular installation. If this equipment does
Boards (PCBs) and all soldered joints have been lead-free since 2005.cause interference to radio or television equipment reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by any combination of the following measures:
(1) Relocate or reorient the receiving antenna (2) Increase the separation between the equipment and the re-
ceiver (3) Plug the equipment into an outlet on a circuit different from that to which the receiver is connected (4)
STATEMENTOFWEEEPOLICYConsult your dealer or experienced radio/television technician for additional assistance.
PMI Audio Group manufactures many complete electronic products which are covered CAUTION Changes or modications to this equipment not expressly approved by the party responsible for
by the European Unions Waste Electric and Electronic Equipment? directive 2002/96/EC compliance could void the user?s authority to operate this equipment.
(WEEE). This directive seeks to ensure that waste electric and electronic equipment is
disposed of in an environmentally responsible manner, at the end of its life cycle. PMI
IMPORTANTSAFETYINSTRUCTIONS
Audio Group takes seriously its obligations under this directive to take back WEEE-af-
fected products and, from 13th August 2005, will mark all such products with the crossed-out
wheeled bin symbol.1. Read these instructions.
2. Keep these instructions.
Business to Business products: PMI Audio Group will cost-neutrally take back WEEE-affected electric and 3. Heed all warnings.
electronic equipment in this category, from 1st January 2006. PMI Audio Group will work with disposal and 4. Follow all instructions.
recycling partners working within the EU. The waste electric and electronic equipment can then be turned over 5. Do not use this apparatus near water. Do not expose to drips or splashes. Do not place any objects lled with
to a disposal and recycling companies in the countries concerned. liquids, such as vases, on the apparatus.
6. Clean only with dry cloth.
Business to Customer products: emerging electric and electronic equipment will be disposed of by local authori-7. Do not block any ventilation openings. Do not install this apparatus in a conned space such as a book case
ties? collection systems. or similar unit. Install only in racks designed for the purpose and in accordance with manufacturers? instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
Dual Use products: this equipment will be disposed of by local authorities? collection systems.ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an
IMPORTANTSAFETYINFORMATIONelectrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE the point where they exit from the apparatus.
COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALI-11. Only use attachments/accessories speciżed by the manufacturer.
FIED SERVICE PERSONNEL.12. Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus combina-
The lightning ash with arrowhead symbol, within equilateral triangle, is intended to aletion to avoid injury from tip-overrt the user to the .
presence of uninsulated dangerous voltage within the products enclosure that may be of 13. Unplug this apparatus during lightning storms or when unused for long periods of time.sufcient
magnitude to constitute a risk of electric shock to persons.14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
The exclamation point within an equilateral triangle is intended to alert the user to the presence spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
of important operating and maintenance (servicing) instructions in the literature accompanying the ap-moisture, does not operate normally, or has been dropped.
pliance.15. Apparatus designed with Class-I construction must be connected to a mains socket outlet with a protective
earthing connection (the third grounding prong).
16. This apparatus may be equipped with a single-pole, rockerstyle AC mains power switch. If so this switch is
located on the front panel and should remain readily accessible to the user.
WARNING: TO AVOID FIRE OR ELECTRIC
17. The manufacturer reserves the right to change the technical specication of the product without prior
SHOCK HAZARD, DO NOT EXPOSE THISnotice.
APPARATUS TO WATER, RAIN OR MOISTURE. |
ACEC
