0eyq0wrtRear Panel
*Turn off all components before making connections.
Rear PanelITUNER Input JacksSpecifications
Connect the output jacks of the tuner to
these jacks.
0Speaker TerminalsContinuous Power Output (RMS):
Connect left loudspeaker to "SPEAKER L",100W + 100W
ITAPE 1 PLAY/REC Jacks
and right loudspeaker to "SPEAKER R". Connect the output (LINE OUT) jacks of(20 - 20,000 Hz, 8 ohms)
Be sure that the loudspeakers are160W + 160W
the tape deck to the PLAY jacks and
connected in phase.connect the input (LINE IN) jacks of the(20 - 20,000 Hz, 4 ohms)
Dynamic Power Output (EIA):
Caution: Short-circuiting of either of thedeck to the REC jacks.120W + 120W (8 ohms)
loudspeaker terminals to the cabinet,ITAPE 2 MONITOR PLAY/REC Jacks220W + 220W (4 ohms)
ground or signal cables can damage theTotal Harmonic Distortion:
amplifier. Short-circuit between theThese jacks are used for connection of a(Continuous rated output power)
second tape deck. Connect the output
loudspeaker terminals will blow the fuses.0.04% (20 - 20,000 Hz,� 6dB, 8 ohms)
Always turn off the amplifier when(LINE OUT) jacks of the tape deck to the0.06% (20 - 20,000 Hz,� 6dB, 4 ohms)
connecting or disconnecting loudspeakerPLAY jacks and connect the input (LINEInput Sensitivity/Impedance:
IN) jacks of the deck to the REC jacks.
cables or signal cables.CD, TUNER, AUX, TAPE;
300 mV/ 20 k ohms
Caution: The loudspeaker output isrAC IN Socket (See page 3.)BALANCED (XLR); 600mV/10 k ohms
balanced. Do not connect any equipmentOutput Level/Impedance:
with unbalanced input (e.g. spectrumtMain POWER Switch (See page 3.)TAPE 1, TAPE 2; 300 mV/100 ohms
Press the ON side of this rocker (seesaw)
analyzers and some electrostaticswitch to turn power ON (standby position). Signal-to-Noise Ratio (IHF-A):
loudspeakers). CD,TUNER,AUX,TAPE;104dBA
Note: Leave this main power switch ON atFrequency Response:
qBalanced Input Connectorall times.CD, TUNER, AUX, TAPE, BALANCED;
The balanced input is connected with XLR20 - 20,000 Hz, +0 /�0.8 dB
plugs in accordance with IECPower Requirements/Power Consumption:
yFuse Holder (See page 3.)
specifications.120 V AC, 60 Hz, 5 A (U.S.A./Canada
PIN 1: GNDModel/General Export Model)
PIN 2: +220 V AC, 50/60 Hz, 500 W (Korea)
PIN 3: �Tape Dubbing230 V AC, 50 Hz, 500 W (Europe/ UK/
General Export Model)
wGND TerminalYou can dub from the deck connected toDimensions (W x H x D):
Connect the ground lead of the turntable toTAPE 1 jacks to the deck connected to TAPE442 x 103 x 383 mm
this terminal.2 jacks. Dubbing from TAPE 2 deck to TAPEWeight (net): 12.0 kg
1 deck is not possible. Standard Accessories:
eAudio Signal Jacks1. Set the playback deck (TAPE 1) to theRemote Control Unit (RC-685) x 1,
IAUX Input Jacksplayback mode, and the recording deckAC cord x 1
Connect the audio output jacks of the(TAPE 2 MONITOR) to the record mode.Improvements may result in features and
VCR to these jacks.Adjust recording level accordingly.specifications being changed without
(Refer to the owner's manuals of thenotice.
ICD Input Jacksdecks.)
Connect the output (LINE OUT) jacks of2. Set the input selector to the tape 1
the CD player to these jacks.position and set the tape 2 monitor
switch to source.
- 5 - |