7- Cassette operationsCassette operations
Recording operations
Recording pre-recorded tapes, records, or other pub-4 Set the DOLBY NR system on or off.
lished or broadcast material may infringe copyright
5 Press tRhEeC ORD key. The deck enters record
laws. Check before recording.standby mode and the indicators light up.
1 Set the REV MODE switch.
6 Play back the source, and adjust the recording
If you want to make a bi-directional recorldeivngel, using the tapIeN PdUeTc kl?esv el control so
set thReE V MODE switch to� th eo rä pos-ithat the loudest sound makes the meters brieAy
tion.reach around t0h edB´ point for normal or
high-position tapes (recording is not possible
Set to the � position if recording is to be made with metal tapes).
on a single side of the tape.
7 Press eithePrA UtShEe orP LAY key to start
2 Load a recordable cassette. Check that the safety recording.
tabs on the spine of the cassette are in place. If
they have been broken off, block the hol es Twoit sht op recording temporarilyP,A UpSrEe ss the
adhesive tape.key. To restart recording, prePsAsU eSitE her the
3 Press tINhPeU T 2 SEL key to select LIeNEit2 her key oPrL AY keys. IfP LtAhYe key whose in-dica
tor is unlit is pressed, the recording direction
or DISC as a recording source.will reverse, aPnLdA Yt hkee y must be pressed
When DISC is selected, the built-in CD playearga?si n to restart recording.
output is selected as a source.8 To stop recording, pSrTeOsPs ktehye.
When LINE2 is selected, the external signal from
the LINE 2 jacks is selected as a source.
Dubbing tapes from the CD deck
To record from the internal CD deck:The DUB indicator ashes.
1 Prepare for recording as described abov e (Tlhoea dC Da starts playback after the eight seconds
tape, set the REV MODE, etc.).at the start of the casDUsBe,t2 tie.nd Tihceat or
lights steadily.
2 Load the source CD disc (OpPrEeNs/s the
CLOSE key, put the disc in the tray, rec ordIf tehde t ape is in record standby mode, recording
side downwards, and close the tray).starts immediately, and the CD starts playback
3 Use tMheE NU key to set the dubbing volume to immediately. DTUhBe,2 indicator lights.
THRU to bypass the input level cBoyn-trol (Tshee deubbing stops when playback reaches the end of
passing the input level for dubbing on thpe CageD , or w23).hen the tape reaches the end of its run (one
side in the case of single-sided (�) reverse mode, both
If you want to adjust the input volume, set the sides in the � reverse mode), whichever comes first.
DUB>VOL menu tOoN and use the leftIN -(tape)
PUT control to adjust the level of signaNloste t fheadt i f tthoe t ape is set to auto-reverse, and the last
the tape from the CD player.item recorded on one side of a tape was not completely
NOTErecorded before the tape was reversed, that item will be
automatically repeated.
If you want to record the tracks on the tape in a
different order from those on the disc, use the pro-Also note that when the tape automatically reverses,
grammed playback mode to rearrange the tracks eight seconds are used as non-recorded time at the
(see Program playback on page 17). Leave the beginning of the second side (the tape is in record
disc in stop mode when you have finished program-mode, but the CD does not play back), again to allow
ming the order.for leader tape at the start of the cassette.
4 Press tDhUeB 2 key.The dubbing process can also be stopped manually with
the STOP key of the cassette deck or the CD deck. All
If the tape is in stop mode, the tape rewinds to other transport keys are disabled.
the beginning of the current side.
NOTE
At the start of the tape, recording starts, but the Dubbing is not possible if a cassette is not loaded,
CD does not start playback for eight seconds.
or a CD is not loaded. It is not possible if the cas-
0 TASCAM CC-222MKIII |
ACEC
