ENGLISH
3PART NAMES AND FUNCTIONS(3) Top panel!4NEXT TR./B TRIM button
Y When the button is pressed during playback,
CAUTION:the NEXT TRACK MODE is selected. If the
(1) Front panel(2) Rear panel
Y Note that there are many buttons working twobutton is pressed again, the *B TRIM MODE is
different function selected by short timeselected. *Only when a seamless LOOP is set.
qwDisc loading slotPOWER button (cON LOFF)
pushing or long pushing (1 second or more). TheIn the standby and pause modes, only the B
Y Load the disc slowly, and release it once theY Push this button to turn power on and off.
mark indicates short time push function andTRIM MODE can be selected.
DN-S1000 starts grabbing the disc in.
CAUTION:mark indicates long time push function.
Y Do not turn off the power while a disc is!5TITLE button
loading or being ejected. Otherwise loadingyPLAY/PAUSE button (13)NOTE:Y CD TEXT:
mechanism may be damaged.Y This button will start or pause playback.Please clean the dirt of the label side of a discWhen there is CD text data, the CD text data
and start loading of the disc.is displayed automatically or when the button
Y Push once to start playback, once again to
The dirt causes a slip of a disc loader roller.is pressed or the track is changed.
Analog output jackspause playback, and once more to resumeeIf no TEXT is available, the display will indicate
playback.
(LINE OUT)ONo TEXT�.
Y This is unbalanced RCA output jacks.Y MP3:
CAUTIONS:uDISC EJECT button
Y Audio signals outputs.When an MP3 file has ID-3 tag data, the title,
Y Do not load discs when the power is turnedY Push this button to eject the disc.
artist name and album name are selected and
off.Y The disc will not eject during playback.
Fader start jackrdisplayed each time the button is pressed.
Y Do not try to forcibly remove a disc onceStop playback before pushing this button.
Y Use this when your mixer has Fader Start
the DN-S1000 has started to grab the disc.
function with 3.5 mm stereo mini cord.!6TIME, CONT./SINGLE button
Y Do not load more than once disc at a timeiCUE button
Y TIME:
or insert anything other than discs.Y Pushing this button in play mode will force theDigital output jack
tA short push will displays mode changes
Otherwise loading mechanism may betrack back to the position which playback
Y Digital data is available from this jack.between ELAPSED TIME and REMAIN TIME.
damaged.started. While in search mode, it makes newY Use 75 &/ohms pin cord for connection.
Y 4-way TOTAL TIME display mode can be
Cue point. (Cue)
Y We recommend you use braided wire typeselected by PRESET(8).
Y In Cue mode, by pushing the CUE button
shielded cable.Y At this time, you can select display mode from
makes a Stutter sound from the Cue point. This
NOTE: The playback level after analogfour modes, TRACK ELAPSED, TRACK
is called Stutter play. (Stutter)
conversion is set to �6dB below theREMAIN, DISC ELAPSED and DISC REMAIN.
usual level to avoid digital distortion.Y CONT./SINGLE:
oScratch Disc
Long pushing play ending mode between
Use this vinyl scratch disc for scan, manual
CONT. (continue: play more tracks) and
search, Pitch Bend and Scratch operations.
SINGLE (stop playing and ReCUEOs back to
your set CUE point).
!0FLIP/CLR button
Y FLIP:Y SINGLE PLAY LOCK:
Use this to select operating mode of A1 and A2When SINGLE PLAY LOCK is selected, track
buttons, from Hot Start mode and Stutterselection during playback is disabled. This
mode. The display will indicate OH/S� or OSTR�prevents playback from stopping when the
Y A1, A2 CLR:Track Select Knob is turned accidentally during
If the A1 or A2 button is pushed while pushingplayback. Play ending mode is the same as
the FLIP button, you can clear the selected Asingle mode.
point.
!7MEMO, PRESET button
By holding down just the FLIP button for more
Y MEMO:
than 1 sec, you can clear A1 and A2 points all
The memo mode starts when this button is
at once.
pushed once in the Cue mode.
Y PRESET:
!1A1, A2 button
Y Using this button you can create starting pointWhen this button is pushed for more than 1
for Hot Start, Seamless Loop and Stutter. sec, the PRESET mode menu is displayed.
The machine status must be in, CUE, PAUSE
!2B buttonor No Disc mode before entering the preset
Y Use this to set the B point to create amode.
Seamless Loop after the A point has been set.
!3EXIT/RELOOP button
Y Use this to exit or return back again to
Seamless loop playback. You can add variety to
looping with this function.
8 |
ACEC
