2
s-bagTMindicator and changing the s-bagTM456Using the blowing outlet (some models)
TM
For peak performance the s-bagshould be changed when full. TheThe blowing outlet can be used for drying damp shoes or clearing
mechanical s-bagTM indicator window will gradually turn red whenleaves etc:
filling and completely red when full. The electronic s-bagTM indicator17 Remove the filter cover.
window will light up when full. If the dust bag should get broken in18 Insert the blowing outlet cover.
the cleaner, take cleaner to service centre for cleaning.19 Insert the hose into the blowing outlet until the catches click to
TM
The s-bagfull indicator may signify that the bag is blockedengage.
(occasionally caused by very fine dust) which will cause loss of
Using the Turbo nozzle (some models)
suction and may result in overheating. If this occurs change the
Precautions: Only use the nozzle on carpets with a pile depth of under
bag even if it is not full.
15 mm. Do not use on animal skins or rugs with long fringes. To avoid
TM
To check the s-bag, the cleaner must be switched on, with all
damaging your carpet, do not keep nozzle stationary whilst brush is
attachments connected and off the floor.
rotating. Do not pass nozzle over mains cable and switch off nozzle
immediately after use.
To change the s-bagTM:
20 Attach turbo nozzle to tubes.
8 Open the cleaner cover.
21 Note: Suction can also be regulated on the turbo nozzle by
TM
9 Lift and pull the sliding tab to remove the s-bagfrom its holder.
opening/closing air vent.
TM
10 Insert the new s-bagby sliding the bag slots into the holder.
Close cover.Cleaning the Turbo nozzle:
22 Disconnect from mains and remove entangled threads
We recommend the s-bagTM is changed after using a carpet cleaning
from brush by snipping with scissors.
powder or if there is a bad smell from the cleaner.
Open cover to remove any debris from inside nozzle.
Note: Only use original s-bagsTM and filters
TMTroubleshooting
s-bag(ref. E200)
Power: If the electric power does not come on, disconnect from mains
Motor protection filter (ref. VF29)and check plugs, cable and fuses where appropriate.
Micro filter (ref. VF16)The cleaner may switch itself off in event of severe blockage or
excessively dirty filters. In such cases, disconnect from mains and
02 Washable reusable HEPA filter (ref. VF25a)
allow to cool for 30 minutes. Clear blockage and/or replace filter(s)
and restart.
s-bagTM safety device
The clearing of blocked hoses is not covered by the guarantee. To avoid
To avoid damaging the cleaner, do not use it without a dust bag. A
blockages and maintain suction efficiency, the floor nozzles should be
safety device is fitted which prevents the cover closing without a dust
cleaned regularly using the hose handle.
bag in place. Do not attempt to force cover shut.
Please see additional Volta information towards the back of this
Changing/cleaning the filtersbooklet.
Never use the cleaner without the filters in place.Water: If water is sucked into the cleaner the motor must be changed
The filters should be changed/cleaned approximately every fifth dustat a service centre.
bag.
To change Motor Protection filter:
11 Open the cleaner cover.
12 Replace the old filter with a new one, ensuring it is securely in
place, and close cover.
To change Micro filter (some models):
13 Press the catch to open the filter cover.
14 Replace the old filter with a new one ensuring it is securely in
place and the cover is properly closed.
Cleaning the 02HEPA filter (some models):
The 02HEPA filter should be cleaned when the indicator light is on
(some models) or every fifth dust bag (some models).
15 Press the catch to open the filter cover and remove filter unit.
16 Rinse the inside (dirty side) of the filter unit under warm tap water
only. Do not use cleaning agents and avoid touching the
delicate filter surface. Tap the filter frame to remove excess
water. Repeat cleaning procedure four times and allow the filter to
air dry. The original filtering performance is now restored. Replace
the unit back into the cleaner and close cover ensuring it is
properly fastened. |
ACEC
