INSTALLATIONOPERATION
Before using
Important
Remove all securing tapes. Wash inside the
Warning
appliance with lukewarm water and bicarbonate of
IF YOU ARE DISCARDING AN OLD APPLIANCEIt must be possible to disconnect the appliance fromsoda (5 ml to 0.5 litre of water).
THAT HAS A LOCK OR CATCH ON THE DOOR,the mains power supply; the plug must therefore be
Do not use soap or detergent as the smell may
YOU MUST ENSURE THAT IT IS MADEeasily accessible after installation.
linger. Dry thoroughly.
UNUSABLE TO PREVENT YOUNG CHILDREN
BEING TRAPPED INSIDE.Control panel
Depending upon the position which you choose for
your appliance, you may wish to reverse the way in
which the door opens. To do this, refer to instructions6
1
on ODoor reversal directions� paragraph.52
43
PositioningAB
This appliance is designed to operate in ambient
A - Thermostat control
temperatures between 10!C (50!F) and 38!C (100!F).
It should be located in a dry atmosphere, out of direct100 mmB - Pilot light
sunlight and away from extreme temperature e.g. not
next to a boiler or radiator, or in a very cold room e.g.To Start the ApplianceUse of an air circulation slider
an outhouse, where the temperatures may fall below
ABAllow the appliance to stand for 2 hours aftercontrol - COOL FLOW CONTROL
10!C (50!F). If these temperatures are exceeded i.e.
installation.
colder or warmer, then the appliance may not operateYour appliance has an air circulation slider control
correctly.Plug in the appliance and switch on at the mainssituated at the rear of the fridge compartment, which
10 mm10 mm
supply. Turn the thermostat control (A) to a midwaycontrols the amount of cold air circulated through the
You should also ensure that air can circulate freely
NP002setting (3-4) and adjust the slider control, situated onfridge compartment.
around the back and the top of the cabinet. There
the back wall of the fridge section, to a midway
must also be at least 100 mm (4�) distance betweenWhen the ambient temperature is between 10!C and
position between OMIN� and OMAX�. The pilot light (B)
the top of the cabinet and any overhanging kitchen16!C, the slider control should be in the OMIN�
will illuminate. Leave the appliance for approximately
furniture (A). Ideally, the appliance should not beposition.
4 hours for the correct temperature to be reached
positioned beneath overhanging furniture (B).
before placing food inside.When the ambient temperature is above 16!C the
There should also be a gap of 25 mm either side ofslider control should be midway between OMIN� and
To switch off the appliance turn the thermostat
the appliance. Do not obstruct the space underneath.OMAX�.
control to position Ol �
When the ambient temperature is very high (i.e. hot
Rear spacers
Setting the temperaturesummer days) position the slider control to OMAX�.
The plastic bag containing all relevant documentation
AThe temperature inside the appliance is regulated by
also contains two spacers to be fitted into special
45°a thermostat with 6 temperature positions and an
holes in the back of the appliance.
OOFF� (l ) position.
PR60
Fit the spacers into the holes, taking care to ensure
Position 1 = minimum coldness
that the arrow (A) is positioned as shown in the
diagram. Then turn them through 45! (arrow (A)Position 6 = maximum coldness
MINMAX
COOL FLOW CONTROL
vertical) until they lock into place.
Turn the thermostat dial to the required position.
The intermediate position is usually the most
DO NOT install in places with restricted ventilation.suitable (3-4).
Adjust the level of the appliance by screwing out theThe thermostat control regulates the temperature
adjustable foot, or feet, at the bottom of the cabinetboth within the fridge and the freezer compartment.
MINMAX
using your fingers.The thermostat setting can vary as the temperatureCOOL FLOW CONTROL
inside the appliance depends on the following
D757/1
factors:
� room temperature
D200� how often the door is opened
� how much food is stored
� position of the appliance
165 |
ACEC
