Filling with saltRinse aid
Rinse aid is automatically added during the last rinse, ensuring
Special salt can be added in one of two ways:thorough rinsing, and spot and streak free drying. The
If you are using dishwasher detergent that already contains dispenser, which is positioned inside the door, holds about 110
salt, the detergent including the salt is placed in the ml of rinse aid, which is sufficient for 16 - 40 dishwashing
programmes, depending upon the dosage setting.
detergent compartment.
- In this case the water softener must manually be set to 1
and electronically to 1 to ensure that the special salt is
Rinse aid can be added in one of two ways:
taken from the detergent container only.
If you are using dishwasher detergent that already contains
If you are using dishwasher detergent and salt separately,
rinse aid, the detergent including the rinse aid is placed in
the special salt is to be put into the salt containerthe detergent compartment..
- In this case the water softener must manually be set to 1 - In this case the rinse aid compartment must be empty
or 2 and electronically between 1 and 5 (depending on and the rinse aid indicator light deactivated.
the water hardness in your area) to ensure that the If in the rinse aid dispenser there is still rinse aid you
special salt is taken from the detergent container onlymust wait until it has finished before using detergent that .
contains rinse aid.
If you are using dishwasher detergent and rinse aid
Only use salt specifically designed for use in
separately, the rinse aid is to be put into the rinse aid
dishwashers.
dispenser.
All other types of salt not specifically designed for use in
a dishwasher, especially table salt, will damage the water- In this case the rinse aid dosage must be set in position
softener.from 1 to 6 (see "Adjusting the dose") and the rinse aid
Only fill with salt just before starting one of the washingindicator light activated.
programmes.
This will prevent any grains of salt or salty water, which
may have been spilt, remaining on the bottom of the
Filling with rinse aid
machine for any period of time, which may cause
corrosion.(Rinse aid dispenser type A)
1.Open the container by pressing the release button (A).
To fill:2.Fill with rinse aid exactly up to the level marked "MAX".
1.Open the door, remove the lower basket and unscrew the
cap of the salt container by turning it anticlockwise.
2.Pour 1 litre of water inside the container (this is necessary
only before filling with salt for the first time).
3.Using the funnel provided,
pour in the salt until the
container is full.SALE
ZOUT
SALT
4.Replace the cap making
SALZ
sure that there is no trace SEL
BR07BR08
of salt on the screw thread
or on the gasket.Ensure that the lid is closed after every refill.
5.Screw on the cap tightly
turning it clockwise until it
stops with a click.Adjusting the dose
According to the finish and drying results obtained, adjust the
The salt container will require topping up periodically. You are
dose of rinse aid by means of the 6 position selector (position
reminded of this by the salt indicator light on the control panel
1 minimum dosage, position 6 maximum dosage).
which comes on when the salt has finished.
Increase the dose if there are drops of water or lime spots on
Do not worry if water over flows from the unit when filling with
the dishes after washing.
salt, this is quite normal.
The dose is factory set in position 4.
The salt indicator light on the control panel can remain
Reduce it if there are sticky
illuminated for 2-6 hours after the salt has been
whitish streaks on the dishes.
replenished, assuming the dishwasher remains switched
on. If you are using salts that take longer to dissolve then
this can take longer. The function of the machine is not
affected.
BR09
23 |
ACEC
