EN 145.L01.1E ABService Modes, Error Codes and Fault Finding
Specifications
Operation hours counter.
Software version.
Option settings.
AAA BCD E E X . Y S D MError buffer reading and erasing.
Software alignments.
How to enter
Use one of the following methods:
E R RX XX XX XX XX XUse a standard customer RC-transmitter and key in the
code ?062596? directly followed by the OSD / STATUS
button or
Via ComPair.
ME N UThe following screen is visible, with SAM at the upper right side
for recognition.
SD M
LLLLA A A B C D X . YS A M
Ma i n^E R RX X XXXXXX X X
?P i c tu r e>B r i g h tn e s sXXXX XXXXXXXXXXXXXXXXX
S oundC o l o u r
F ea t u r e sC o n t r as tCL E A RC L E A R ?
I n s t a l lS h a r p n essOP T I O N S>
Co l o u r T e m pAK B0 / 1
St o r eTU N E R>
vWH I T E T O N E>
GE O M E T R Y>
AU D I O>
OS D / S T A TU SCL 16532020_061.eps
150401
Figure 5-4
SD M1. LLLL This is the operation hours counter. It counts the
normal operation hours, not the standby hours.
2. AAABCD-X.Y This is the software identification of the main
micro controller:
A = the project name (L01).
B = the region: E = Europe, A = Asia Pacific, U =
NAFTA, L = LATAM.
C = the software diversity: D= DVD, F= full TXT, M=
mono, T= 1 page TXT.
CL 16532020_060.pdfD = the language cluster number.
220501X = the main software version number.
Y = the sub software version number.
3. SAM Indication of the actual mode.
Figure 5-3
4. Error buffer Five errors possible.
5. Option bytes Seven codes possible.
How to navigate6. Clear Erase the contents of the error buffer. Select the
Use one of the following methods:CLEAR menu item and press the CURSOR RIGHT key.
When you press the MENU button on the remote control, The content of the error buffer is cleared.
the set will switch between the SDM and the normal user 7. Options To set the Option Bytes. See chapter 8.3.1 for a
menu (with the SDM mode still active in the background). detailed description.
Return to the SDM screen with the OSD / STATUS button.8. AKB Disable (0) or enable (1) the ?black current loop? (AKB
When you press the OSD / STATUS button on the remote = Auto Kine Bias).
control, the menu will show or hide the error buffer. This 9. Tuner To align the Tuner. See chapter 8.3.2 for a detailed
feature is available to prevent interference during description.
waveform measurements.10. White Tone To align the White Tone. See chapter 8.3.3 for
On the TV, press and hold the 'VOLUME down' and press a detailed description.
the 'CHANNEL down' for a few seconds, to switch from 11. Geometry To align the Geometry. See chapter 8.3.4 for a
SDM to SAM and reverse.detailed description.
12. Audio To align the Audio. See chapter 8.3.5 for a detailed
How to exitdescription.
Switch the set to STANDBY by pressing the power button on
the remote control transmitter (if you switch the set 'off' by How to navigate
removing the Mains power, the set will return in SDM when Use one of the following methods:
Mains power is re-applied). The error buffer is cleared.In SAM, select menu items with the CURSOR UP/DOWN
key on the remote control transmitter. The selected item
5.2.2 Service Alignment Mode (SAM)will be highlighted. When not all menu items fit on the
screen, move the CURSOR UP/DOWN key to display the
Purposenext / previous menu items.
To perform alignments.With the CURSOR LEFT/RIGHT keys, it is possible to:
To change option settings.- (De)activate the selected menu item.
To display / clear the error code buffer.- Change the value of the selected menu item. |