Introduction
Identification of controls (continued)
Inserting batteries
123Open the battery compartment Install two R03/AAA batteriesReplace the compartment
cover in the direction of the (supplied), paying attention tocover.Introduction
Remote controlarrow.the polarity indicated in the
battery compartment.
The instructions in this manual describe the function on the remote control. See the page in for details.
EJECT button32POWER button21
TV/DVD button31SLEEP button24
Direct channel selection
buttons (0-9)23
Numbered buttons (0-9)26
Operation
RECALL button24CH RTN button24
ZOOM button34
"Aim the remote control at the remote sensor and press control buttons to operate.
JUMP button34MUTE button24"Operate the remote control within 30° angle on either side of the remote sensor, up to a distance of approx. 5
INPUT SELECT button16VOL +/ buttons23meters.
PLAY MODE button35CANCEL button26
GAME button16
TOP MENU button37*DVD MENU button37
Direction buttons( / / / )21
MENU button21CH +/ buttons22
SETUP button43ENTER button21Approx. 5 meters
RETURN button43
PLAY button31
STOP button31PAUSE button32
SKIP buttons33
REV button33
FWD button33
CLOSED CAPTION button25
SLOW buttons33REPEAT A-B button35
Caution:
ANGLE button37" Never throw batteries into a fire.
AUDIO button30SUBTITLE button38
Notes:
" Be sure to use AAA size batteries.
" Dispose of batteries in a designated disposal area.
" Attention should be drawn to the environmental aspects of battery disposal.
" Do not mix different battery types or combine used batteries with new ones.
" If the remote control does not operate correctly, or if the operating range becomes reduced, replace both
batteries with new ones.
*DVD MENU button" If the batteries are dead or if you will not be using the remote control for a long time, remove the batteries to
Use the DVD MENU button toprevent battery acid from leaking into the battery compartment.
display the menu included on
many DVD video discs.
To operate a menu, follow the
instructions in DVD menu. 37
1213
Connections
Antenna connectionsCable TV connections
If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. IfThis TV/DVD has an extended tuning range and can tune most cable channels without using a Cable TV converter box.
you are using a cable TV service (CABLE), see page 15 for Cable TV connections.Some cable companies offer premium pay channels in which the signal is scrambled. Descrambling these signals for
normal viewing requires the use of a descrambler device which is generally provided by the cable company.
Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire)For subscribers to basic cable TV service
AntennaFor basic cable service not requiring a converter/descramblerConnections
Connect the 75 ohm cable from the combinationjack
AntennaAntennabox, connect the Cable TV 75 ohm coaxial cable directly to the
jackjackVHF/UHF antenna to the antenna jack on the backAntenna jack on the back of the TV/DVD.
of the TV/DVD.
75 ohm
If your combination VHF/UHF antenna has a 300coaxial cable
75 ohm coaxial cableohm twin-lead wire, use the 300-75 ohm matching
(not supplied)transformer.
300-75 ohm matchingFor subscribers to scrambled cable TV service
transformer (supplied)
If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the
incoming 75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect
the output jack of the converter/descrambler box to the antenna jack on the TV/DVD. Follow the connections
shown below. Set the TV/DVD to the output channel of the converter/descrambler box (usually channel 3 or 4)
Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires)and use the converter/descrambler box to select channels.
AntennaConnect the UHF 300 ohm twin-lead wire to the
300-75 ohm matchingcombiner (not supplied). Connect the VHF 300Incoming
jackAntenna
transformer (supplied)ohm twin-lead wire to the 300-75 ohm matching75 ohm75 ohm cable tojack
transformer. Attach the transformer to the combiner,Cable TVConverter/TV/DVD
then attach the combiner to the antenna jack on thedescrambler
back of the TV/DVD.
Combiner
(not supplied)
UHF 300 ohmVHF 300 ohm
twin-lead wiretwin-lead wire
(not supplied)(not supplied)For subscribers to unscrambled basic cable TV service with scrambled
premium channels
If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the
Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)use of a converter/descrambler box, you may wish to use a signal splitter and an A/B Switch box (available from the
cable company or an electronics supply store). Follow the connections shown below. With the switch in the B
position, you can directly tune any nonscrambled channels on your TV/DVD. With the switch in the A position, tune
Connect the VHF 75 ohm cable and UHF 300 ohmyour TV/DVD to the output of the converter/descrambler box (usually channel 3 or 4) and use the converter/
Antennatwin-lead wire to the combiner (not supplied).descrambler box to tune scrambled channels.
jackAttach the combiner to the antenna jack on the back
of the TV/DVD.
VHF 75 ohmConverter/
(not supplied)Incomingdescrambler
Antenna
75 ohm75 ohm cablejack
CombinerCable TVAto TV/DVD
(not supplied)SplitterA/B switchB
UHF 300 ohm
twin-lead wire
(not supplied)
1415 |
ACEC
TOSHIBA
