Technical FeaturesTechnical FeaturesAdditional InformationGetting StartedTechnical Features
Notes
Power Saving FunctionY When your computer is in a power saving mode, MONITOR ISPreset ModesWarning Messages
IN POWER SAVE MODE appears on the screen if you press any
This monitor meets the power-saving guidelines set bybutton on the monitor (page 15). After a few seconds, theResolutionHorizontalVerticalGraphicsIf no pictures appears on the screen, one of the following
VESA and ENERGY STAR, as well as the more stringentmonitor enters the power saving mode again. Once theNo.(dots ´ lines)FrequencyFrequencyModemessages appears on the screen.
horizontal and vertical sync signals are detected, the monitor
NUTEK .
automatically resumes its normal operation mode.1640 ´ 48031.5 kHz60 HzVGAINFORMATION
If the monitor is connected to a computer or video graphicsY The power management feature is invoked when the computerMONITOR IS WORKING
board that is VESA DPMS (Display Power Managementrecognizes that you have not used your mouse or keyboard for a2640 ´ 48037.5 kHz75 HzVESA
Signaling) compliant, the monitor will automatically reduceuser-definable period of time.3640 ´ 48043.3 kHz85 HzVESAOUT OF SCAN RANGECHANGE PC SETTING
power consumption in three stages as shown below.Y IBM recommends that you switch off your monitor at the end of
each working day, or whenever you expect to leave it unused for4800 ´ 60046.9 kHz75 HzVESA
long periods during the day.5800 ´ 60053.7 kHz85 HzVESAMONITOR IS WORKING or MONITOR IS IN POWER
SAVE MODE appears in the row 1.
Power consumptionScreenHorizontalVerticalPowerRecovery timeu indicator61024 ´ 76860.0 kHz75 HzVESA
modesync signalsync signalconsumption71024 ´ 76868.7 kHz85 HzVESAIf MONITOR IS WORKING appears on the screen
1Normal operationactivepresentpresentL 130 WNGreen
81280 ´ 102480.0 kHz75 HzVESA1 The monitorOs condition
2Standby (1st mode)blankabsentpresentL 15 WApprox. 5 sec.Green and orangeMONITOR IS WORKING
alternate91280 ´ 102491.1 kHz85 HzVESAThis indicates that the monitor is working properly.
3Suspend (2nd mode)blankpresentabsentL 15 WApprox. 5 sec.Green and orange101600 ´ 120093.8 kHz75 HzVESA2 The input signal condition and the remedies
(sleep)*alternate
CHECK SIGNAL CABLE
4Active-off (3rd mode)blankabsentabsentL 3 WApprox. 15 sec.OrangeThis indicates that no signal is input. Check that the
(deep sleep)*video signal cable is properly connected and all plugs
5Power-offNNNL 0.5 WNOffare firmly seated in their sockets.ENDisplaying the MonitorOs
OUT OF SCAN RANGE and CHANGE PC SETTING
1-7* OSleep� and Odeep sleep� are power saving modes defined by the Environmental Protection Agency.InformationThese indicate that the input signal is not supported byF
the monitorOs specifications. Check that the video
frequency range is within that specified for the monitor.ESYou can display the model name, serial number and year of
manufacture using the monitor�s INFORMATION OSD.(Horizontal: 30 � 94 kHz, Vertical: 48 �120 Hz)
Damper WiresPlug & PlayPress and hold the button for 5 seconds.CIf MONITOR IS IN POWER SAVE MODE appears on the
The INFORMATION OSD appears.
When viewing a white background, very thin horizontalThis monitor complies with the DDC1, DDC2B and DDC2Biscreen
lines may be visible on the screen as shown below. TheseDisplay Data Channel (DDC) standards of VESA.Example:1 The monitorOs condition
lines are the shadows of the damper wires and areWhen a DDC1 host system is connected, the monitorMONITOR IS IN POWER SAVE MODE
characteristic of CRTs that use aperture grilles. The wiressynchronizes with the V. CLK in accordance with the VESAINFORMATIONThis indicates that the computer is in power saving
are attached to the aperture grille on the inside of thestandards and outputs the EDID (Extended DisplayMODEL: IBM P76mode. This message is displayed only when your
Trinitron tube and prevent the vibration of the apertureIdentification Data) to the data line.SER NO:12-34567MANUFACTURED:1999-52computer is in a power saving mode and you press any
grille.When a DDC2B or DDC2Bi host system is connected, theof the buttons on the monitor.
monitor automatically switches to the appropriate standard.
The INFORMATION OSD includes the model name, serial2 The remedies
Damper wires
number, and manufactured year.ACTIVATE USING PC
Try pressing any key on the computer keyboard or
The OSD automatically disappears after about 30 seconds.moving the mouse, and confirm that your computerOs
graphic board is completely seated in the correct bus
slot.
For more information, see OTroubleshooting� on page 16.
1415 |
ACEC
SONY
