Parts and their functions
MONI LINK:Shading link settingRPED, BPED: R, B pedestal level
This is used to set whether to link theAdjustment range: �100 to +100
monitor when the R, G or B shadingThe level is increased or decreased from
switch has been selected.the level at the pedestal position where
ANALOG:CCU analog output settingthe black balance was attained.
This is used to set the analog output ofWhen the black balance is adjusted, 0 is
the CCU to the HD or SD component.set as the adjustment value.
SDI4 OUT:HD SDI4 output selection
This is used to set the HD SDI4 output ofGain control switch [GAIN CONTROL]
the CCU as the PM or normal output.This is selected to adjust the white balance. When it is
SYNC:Sync waveform addition settingselected, its lamp lights.
This is used to select whether to add theG GAIN:Adjustment range: �100 to +100
sync waveform to the analog output.(Amount by which the G gain is to be
TYPE:Analog sync waveform settingincreased or decreased from its
This is used to set the sync waveform toreference setting)
be added to the HD analog output toR GAIN, B GAIN: Adjustment range: �100 to +100
binary or tri-level.(Amount by which the R or B gain is to
H_CO (HDTV): Horizontal sync signal phase coarsebe increased or decreased as
adjustmentreferenced to their levels at the
This is used to coarsely adjust the phasepedestal position where the white
in relation to the HDTV genlock syncbalance was attained; when the white
signal.balance is adjusted, 0 is set as the
H_FIN (HDTV): Horizontal sync signal phase fineadjustment value.)
adjustment
This is used to finely adjust the phase in
relation to the HDTV genlock sync signal.Gamma curve control switch [GAMMA CONTROL]
H_CO (SDTV): Horizontal sync signal phase coarseThis is selected to adjust the gamma correction.
adjustmentSince the M GAM adjustment value is independent of the
This is used to coarsely adjust the phaseR and B GAM adjustment values, the R and B GAM
in relation to the SDTV genlock syncvalues remain unchanged even when M GAM is
signal.changed.
H_FIN (SDTV): Horizontal sync signal phase fineWhen the switch is selected, its lamp lights.
adjustmentM GAM:Master gamma
This is used to finely adjust the phase inAdjustment range: 0.600 to 0.300
relation to the SDTV genlock sync signal.RGAM, BGAM: Adjustment range: �75 to +75
SCCO:Subcarrier phase coarse adjustment
This is used to coarsely adjust the phaseFlare control switch [FLARE CONTROL]
of the subcarrier signal in relation to theThis is selected to change the amount of flare correction.
SDTV genlock sync signal.When it is selected, its lamp lights.
SCFIN:Subcarrier phase fine adjustmentRFLR, GFLR, BFLR: R, G and B flare
This is used to finely adjust the phase ofAdjustment range: �50 to +50
the subcarrier signal in relation to the(Flare correction operation is
SDTV genlock sync signal.turned off at 0.)
SH_H:SD/HD horizontal phase
White clip control switch [WHITE CLIP CONTROL]
This is used to adjust the horizontalThis is valid when the lamp of the WHT CLIP OFF switch
phase of the SDTV output and HDTVamong the MODE ON/OFF switches is off, and it is
output.selected to change the white clip level. When it is
SH_V:SD/HD vertical phase selected, its lamp lights.
This is used to set the vertical phase ofWHT CLIP: White clip
the SDTV output and HDTV output toAdjustment range: 95% to 110%
line 0 and line 90 (advanced by 90H for
HDTV).
Knee control switch [KNEE CONTROL]
Pedestal control switch [PED CONTROL]This is selected to adjust the knee slope and knee point.
This is selected to adjust the R, G and B pedestal levelsMPNT:Master knee point
in relation to the master pedestal position.Adjustment range: 105% to 85%
When it is selected, its lamp lights.RPNT, BPNT: R and B knee points
GPED:G pedestal levelAdjustment range: +10% to �10%
Adjustment range: �100 to +100 (amountMSLP:Master knee slope
of G pedestal offsetAdjustment range: 63 to 0
from master pedestal)RSLP, BSLP: R and B knee slopes
Adjustment range: +32 to �31
8 |
ACEC
PANASONIC
