2. AR-NC5J setup items
After completion of installation, perform setup of the environmental variables. Explanations on the variables are given below.
A. General
Name
Factory setupDescriptions
TelnetWeb pageNIC Manager
Change root Change Admin Admin SharpThe administrator password of the AR-NC5J is set with ASCII
PasswordpasswordPasswordcharacter codes. This password is used for identification when
changing setup by Telnet, a Web page, or a setup utility.
Remark: Indicated as "*" for security.
Print status after Print status after Print status after NOWhen booting the AR-NC5J, select whether to print the status page or
Boot-upBoot-upBoot-upnot.
B. TCP/IP and related items
Name
Factory setupDescriptions
TelnetWeb pageNIC Manager
TCP/IP Protocol TCP/IP Protocol TCP/IP protocol ENABLEUsed to enable/disable TCP/IP protocol. This setup will affect the
is used.operations of LPR, FTP, TELNET, SNMP, HTTP, and the setup utility
(for TCP/IP).
DHCP/BOOTP DHCP/BOOTP DHCP/BOOTP ENABLE Used to enable/disable the operation of DHCP/BOOTP protocol. The
is used.DHCP/BOOTP protocol acquires an IP address from the DHCP server
or the BOOTP server when booting. To set an IP address of the AR-
NC5J, a DHCP server or a BOOTP server which has been properly
set should be operating in the sub network. The AR-NC5J
automatically recognizes DHCP and BOOTP, and employs as its
address whichever replies to it first.
RARPRARPRARP is used. ENABLEUse to disable/enable the RARP protocol operation. The RARP
protocol acquires an IP address from the RARP server. To set an IP
address of the AR-NC5J by RARP, the RARP server which has been
properly set should be operating in the sub network.
IP AddressIP AddressIP Address0.0.0.0Used to set an IP address of the AR-NC5J. The set value is in the
form of decimal number of "xxx.xxx.xxx.xxx."
Subnet MaskSubnet MaskSubnet Mask0.0.0.0Used to set the subnet mask of the AR-NC5J. The set value is in the
form of decimal number of "xxx.xxx.xxx.xxx." When "0.0.0.0" is set,
this item is disabled, and the subnet mask corresponding to the IP
address is automatically used.
Default Default Default 0.0.0.0Used to set an IP address of the gateway. The set value is in the form
GatewayGatewayGatewayof decimal number of "xxx.xxx.xxx.xxx." The gateway must exist in the
same sub network as the AR-NC5J. When "0.0.0.0" is set, this item is
disabled.
Use FTP/LPD Use FTP/LPD Use FTP/LPD NOUsed to set whether to output the banner page when printing with LPR
BannerBannerBanneror FTP.
C. NetWare and related items
Name
Factory setupDescriptions
TelnetWeb pageNIC Manager
Netware Netware Use Netware ENABLEUsed to disable/enable the NetWare protocol operation. This setup
ProtocolProtocolProtocol.will affect the operations of the print server, the remote printer, and the
setup utility (for IPX/SPX).
Frame TypeFrame TypeFrame Type802.2Used to set the default frame type which is used by the AR-NC5J. If
the set frame type does not work, another frame type is automatically
selected.
Operation Mode Operation Mode Operation Mode PSERVERUsed to set the priority operation mode (print server/remote printer) of
the AR-NC5J. If the set mode does not work, another mode is
automatically selected and tried.
Printer NamePrinter NamePrinter Name"SCxxxxxx-prn1"Used to set the printer name which is registered in the print server
(xxxxxx is the lower 6 information in the NetWare server. This setup must be identical to the
digits of Mac address.)setup of the printer name registered in the NetWare server.
Print Server Print Server Print Server "SCxxxxxx"Used to set the print server name when the AR-NC5J is booted in the
NameNameName(xxxxxx is the lower 6 print server mode. Since this setup is used as an identification
digits of Mac address.)element in a network with the NetWare protocol, it must be different
from the other NetWare product names. It is used as the login name to
log in the NetWare server.
AR-NC5J/NC5JG/NC5JW - 4 |
ACEC
SHARP
