AH-X08BE/10BE/13BE
AY-X08BE/10BE/13BE
AY-X08BE-C/10BE-C
AU-X08BE/10BE/13BE
AE-X08BE/10BE/13BE
AE-X08BE-C/10BE-C
board
Solution
Compressor lodOverheat of the compressor
compressor.assembly.assembly or only TH2.moduleassembly.assembly.assembly (Current transformer wire break.) assembly.outdoor board assembly.
: Blinks 3 times at 0.2-second intervals1. Apply an external shock to the 2. Replace the compressor.1.Clear the discharge outlet. 2.Assure power supply voltage. 3.Refill to rated amount. 4.Replace the outdoor ther-mistor 5.Replace the indoor control 1. Replace power transistor 1.Replace the outdoor thermistor 1. Reattach. 2.Replace the outdoor thermistor 1.Replace the outdoor control board 1. Clear the discharge outlet.1. Replace the power factor module.1. Replace fan motor 2. Reattach. 3.Replace the indoor control board 1. Rewire.1. Rewire.1. Rewire. 2.Replace the fuse, replace the 3. Replace the board. 4. Replace the board.
1
sec.
1
sec.
: ON1 sec.
0.6 sec.
1
1sec.
sec.
10.6 sec.
: OFFsec.
11
sec.sec.
1
0.6 sec.sec.
1
1sec.
sec.
10.6 sec.
sec.
What to check, procedure11
sec.sec.
1 time
0.6 sec.0.6 sec.2 times
11
secsec.
11
sec..sec.
: Blinks at 2-second intervals
outdoor unit (see Figure 2).the indoor unit (see Figure 1).outdoor unit (see Figure 2).unit control board?
Does compressor active ? Does it go off immediately after active ?1. Is the discharge outlet of the outdoor unit clogged ? 2. Is the power supply voltage at least 198 V at full power operation ? 3. Check for refrigerant leaks at the tubing connections. 4. Measure the resistance of compressor thermistor TH1 on the 5. Measure the resistance of heat exchanger pipe thermistor TH2 on 1. Check the circuit in the power transistor module. 2. Is the outdoor fan revolving ?1. Measure the resistance of thermistor TH2 on the outdoor unit (see Figure 2).1. Are the connectors of the outdoor unit thermistors well attached ? 2. Measure the resistance of thermistors TH1 and TH2 on the 1. Can voltage be detected at the current transformer on the outdoor 1. Is the discharge outlet of the outdoor unit clogged ?1. CHeck wiring of power factor module.1. Is the fan motor locked ? 2. Is the wiring connector firmly fitted ? 3. Is the speed signal applied to the motor ?1. Check the wiring between units.1. Check the wiring between units.1. Check the wiring between units. 2. Check the fuse in the outdoor unit. 3. Indoor control board. 4. Outdoor control board.ON OFFON OFF
Normal
Diagnosis
Compressor lock errorOverheat of the comp- ressor error (protector operating) or outdoor compressor thermistor TH1 shortDC overcurrent errorShort circuit of the thermistor errorOpen circuit of the thermistor errorAC abnormal current errorAC overcurrent errorIndoor fan out of orderSerial shortSerial openOutdoor power supply does't turn on. Wiring mistake.
OnceTwice3 times4 times5 times6 times7 times11 timesPower factor module error
Display by outdoor unit lamp LED 1
4 seconds off
Display by indoor unit operation lamp
Displayed in a pattern which comes on at the same time as the timer lamp
completely stopped
completely stopped2.If the power plug is removed from the outlet or the breaker is switched to3.Example of outdoor unit LED 1 blinking :
Outdoor unit
Indoor and outdoor unit
operating
NormalIndoor unit
Condition of indoor and outdoor unit
BREAK DOWN DIAGNOSIS PROCEDURE Self-diagnostic procedure using display mode If the timer lamp blinks during operation, the problem can be diagnosed using the following table.Note:1.Normal : Only the timer lamp blinks. Error : Displayed by blinking of run lamp (above table). "OFF", the self-diagnostic memory will be erased.
33 |
ACEC
SHARP
