AVR35 om (H) 2/5/99 10:41 AM Page 28
Programming the Remote
28
The AVR35 is equipped with a powerful2. Turn on the unit you wish to programthe volume, channel and transport
remote control that will control not onlyinto the AVR35 remote.controls, as appropriate. If all func-
the receiverOs functions, but also most CDtions do not work properly, you may
players and cassette decks manufactured3. Press and hold both the Deviceneed to use a different remote code.
by Harman Kardon. For increased flexi-Control Selectorcfor the type
bility, the remote also contains the codesof product to be entered (e.g., VCR,7. If a code cannot be entered to turn the
for most popular brands of audio andTV) and the Mutebutton ` at theunit off, if the code for your product
video equipment, including CD players,same time. Hold both buttons untildoes not appear in the tables in this
cassette decks, TV sets, cable boxes, VCRs,the red light under the button staysmanual, or if not all functions oper-
satellite receivers and other home-theaterlit. Note that the next step must takeate properly, try programming the
equipment. Once the AVR35Os remote isplace while the red light is on, and itremote with the Auto Search Method.
programmed with the codes for the pro-must begin within 20 seconds after
ducts you own, it is possible to eliminatethe light illuminates.IMPORTANT NOTE: The OTAPE� button
most other remotes and replace themmay be programmed to control a DVD or
with the convenience of a single, backlit4. Point the AVR35Os remote towards theLD player, instead of a tape deck, by using
universal remote control.unit to be programmed, and enter thethe codes shown on page 32. Similarly,
first three-digit code number using thethe OCBL/SAT� button may be used to
Programming the RemoteNumericbuttons n. If the unitcontrol a cable box, satellite receiver or
turns off, the correct code has beenweb browser box, depending on the code
As shipped from the factory, the remote entered. Press the Device Controlyou enter.
is fully programmed for all AVR35 func-Selectorcagain, and note that
tions, as well as those of most Harmanthe red light will flash twice to confirmAuto Search Method
Kardon CD changers, CD players and cas-the entry before going dark.
sette decks. In addition, by following oneIf the unit you wish to include in the
of the methods below, you may program5. If the device to be programmed inAVR35Os remote is not listed in the code
the remote to operate a wide range ofdoes NOT turn off, continue to entertables in this manual, or if the code does
devices from other manufacturers.the three-digit code numbers untilnot seem to operate properly, you may
the equipment turns off. At this point,wish to program the correct code using
Direct Code Entrythe correct code has been entered.the Auto Search method as shown below.
Press the Device Control Selector
This method is the easiest way tocagain, and note that the red1. Turn on the unit that you wish to
program your remote to work withinclude in the AVR35 remote.
different products.light will flash twice to confirm the
entry before going dark.
2. Press the Device Control Selector
1. Use the tables in the following pagescfor the type of product to be
6. Try all of the functions on the remote
to determine the three-digit code orto make certain that the productentered (e.g., VCR, TV) and the Mute
codes that match both the productoperates. Keep in mind that manybutton ` at the same time. Hold
type (e.g., VCR, TV), but also theboth buttons until the red light under
manufacturers use a number of dif-
specific brand name. If there is moreferent combinations of codes, and itthe button stays lit. Note that the next
than one number for a brand, makestep must take place while the red
is a good idea to make certain that
note of the different choices.not only the Power control works, butlight is on, and it must begin within
20 seconds after the light illuminates. |
ACEC
HARMAN KARDON
