PREPARING THE LAUNDRYSELECTING A PROGRAMME & OPTIONSDAILY MAINTENANCE & CLEANINGAFTER-SALES SERVICE
Programme and Options:Clean the lint filter at the end of every
1. Check that all fastenings are closed and that If, after carrying out the above checks the
? To select a programme, turn the programme drying cycle:
pockets are empty. malfunction persists or appears again, turn
selector knob. The Start/Pause indicator
2. Turn the articles inside out.1. Open the door.the dryer off and call our After-Sales Service
lamp is blinking ?? , indicating that the
3. Place laundry loosely in the drum to make 2. Pull the filter upwards.(refer to guarantee).
cycle needs to be started.
sure it doesn?t become tangled.Please specify:
? To select an option, press the corresponding 3. Remove lint using a soft brush or your
Sort laundry as follows:fingertips.? The nature of the fault.
button. The indicator lamp in the button
A) By care symbols confirms that a selection has been made.4. Push the filter back into place. ? The dryer type and model.
(on the collar or inside seam):? Press the button again to cancel the option.? The service code (the number after the word
TROUBLESHOOTING GUIDE
Service on the adhesive rating plate) on the
Suitable for tumble dryingSTARTING & COMPLETING A PROGRAMME
If a fault occurs, before contacting our After-right-hand side when the door is open.
1. Having selected the desired programme and Sales Service, make the following checks to try ? Your full address and phone number.
Tumble drying with reduced drying
options, press the Start button.and remedy the problem:
intensity only
If the laundry is not removed at the end of Drying takes too long / laundry is not dry
Do not tumble drythe drying cycle, an automatic anti-crease enough:
cycle will operate for maximum 60 min. The ? Was the correct programme selected?
B) By amount and thickness/weightdrum rotates at regular intervals, preventing
Whenever the load to be dried exceeds dryer the laundry from creasing.? Was the inserted laundry too wet (Washing
capacity, separate laundry according to This Anti-Crease cycle can be extended up to machine spin speed less than 800 rpm)?
weight (e.g. towels from thin underwear).12h when Anti-Crease option has been ? Is the lint filter dirty (filter indicator lamp on)?
C) By type of fabricsselected.The dryer does not operate:
Cotton/linen: Towels, cotton jersey, bed and 2. On completion of the programme, set the (after a power failure and/or interruption to the
table linen made of cotton or linen.programme selector knob to position ?0?.mains supply, always press the Start button).
Synthetics/Easy Care: blouses, shirts,
? Is the plug properly inserted into the mains CHANGING A PROGRAMME
overalls, etc. made of polyester or
electricity socket?
polyamide, as well as cotton/synthetic When changing the programme during the drying
? Is there a power failure?
mixes.cycle, the dryer stops. The Start/Pause indicator
D) By drying levellamp is blinking ?? .? Has the fuse blown?
? Sort into: iron dry, cupboard dry, etc.To operate the new programme, press the? Is the door well closed?
Do not tumble dry: Woollens, silk, nylon Start/Pause button again. ? Has the programme been selected?
stockings, delicate embroidery, fabrics with ? Has the Start/Pause button been pressed?INTERRUPTING A PROGRAMME
metallic decorations, bulky items such as Lint filter indicator lamp light on:
sleeping bags, etc.To interrupt the dryer during operation? Is the lint filter clean?
Important: only use specific indicated dryer-1. Set the programme selector knob to
? Is the vent hose blocked?
safe additives and rinse items that have been Airing ?? .
treated with stain remover thoroughly in plenty 2. Press the Start button. All programme sequence indicators blinking:
of water before drying. Only use specific Wait at least 5 minutes before opening the ? Service call necessary.
indicated dryer-safe plastic items and never door to allow the dryer to cool down.
dry rubber or articles contaminated with For your safety the programme stops
vegetable oil in the dryer.automatically if you open the door.
3. To restart, after door opening, close the door
and press the Start/Pause button again.
5019 307 00318 |
ACEC
WHIRLPOOL
