Maintenance & safety (See 8)Troubleshooting
CD player and CD handling Safety informationIf a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
Y If the CD player cannot read CDs correctly,Y Place the set on a flat, hard and stable surface
use a cleaning CD to clean the lens beforeso that the system does not tilt.
taking the set to repair.WARNING:Do not open the set as there is a risk of electric shock.Under no
Y Do not expose the set, batteries, CDs tocircumstances should you try to repair the set yourself,as this will
Y The lens of the CD player should never behumidity, rain, sand or excessive heat causedinvalidate the guarantee.
touched!by heating equipment or direct sunlight.
Y Sudden changes in the surrounding Y The apparatus shall not be exposed to drip-
ProblemY Quit program mode
temperature can cause condensation on theping or splashing.
lens of your CD player. Playing a CD is then� Possible cause--, Er or 01indication
Y Adequate ventilation with a minimum gap of
not possible. Do not attempt to clean theY Remedy
15cm (6 inches) between the ventilation� No CD inserted
lens but leave the set in a warm environment
holes and surrounding surfaces is necessary
until the moisture evaporates.No sound /powerY Insert a CD
to prevent heat build-up.
� CD badly scratched or dirty
YAlways close the CD-tape door to avoid dust� Volume not adjusted
Y Do not cover the ventilation openings withY Replace/ clean CD, see Maintenance
on the lens.Y Adjust the VOL
items such as newspapers, table-cloths, cur-Note:A CD badly scratch or dirty may result in
YTo clean the CD, wipe in a straight line fromtains, etc.� Power cord not securely connected
improper operation.
the center towards the edge using a soft,Y Connect the AC power cord properly
Y No objects filled with liquids, such as vases,� Laser lens steamed up
lint-free cloth. Do not use cleaning agents as� Batteries dead/ incorrectly inserted
shall be placed on the apparatus.YWait until lens has cleared
they may damage the disc.
Y Insert (fresh) batteries correctly
Y No naked flame sources, such as lighted can-� CD-R/CD-RW is blank or not finalized
Y Never write on a CD or attach any stickers� Headphones connected to the set
dles, should be placed on the apparatus.Y Use a finalized CD-R/CD-RW or suitable CD
to it.Y Disconnect headphones.
Y The mechanical parts of the set contain Audio disc only
Tape deck maintenance� CD contains non-audio files
self-lubricating bearings and must not be oiled
Y Press , § once or more to skip to a CD audioPoor cassette sound quality
To ensure quality recording and playback ofor lubricated.
track, instead of the data file.
the tape deck, clean parts A, B and C as� Dust and dirt on the heads,etc.
YTo clean the set, use a dry cloth. Do not use
shown, once a month. Use a cotton bud Display does not function properly/ No
any cleaning agents containing alcohol,Y Clean deck parts, see Maintenance
slightly moistened with alcohol or a specialreaction to operation of any of the con-
ammonia, benzene or abrasives as these may� Use of incompatible cassette types (METAL or
head cleaning fluid to clean the deck.trols
harm the housing.CHROME)
1 Open the cassette holder by pressing� Electrostatic discharge
Y Only use NORMAL (IEC I) for recording
STOPYEJECT.Y Switch off and unplug the set. Reconnect after a
2 Press PLAY and clean the roller C.few secondsRecording does not work
3 Press PAUSE and clean the heads A, andThe CD skips tracks� Cassette tab(s) may be broken
the capstan B.Y Apply adhesive tape over the missing tab space
� CD damaged or dirty
4 After cleaning, press STOPYEJECT.
Y Replace or clean CD
� Cleaning of the heads can also be done by
playing a cleaning cassette through once.
� Program is active |
ACEC
PHILIPS
