EnglishControls/Power SupplyPower SupplyBasic Operation/ Radio
Y Incorrect use of batteries can cause
Supplied AccessoriesBack/bottom panels (See 1) Basic operation
electrolyte leakage and will corrode the
� AC power cord 9 Telescopic antenna � improves FM compartment or cause the batteries to burst:
Switching on and off and selecting the
reception
Y Do not mix battery types:e.g.alkaline with car-function
0 Battery door � open to insert 6 x 1.5V
Top/front panels (See 1) bon zinc.Only use batteries of the same type1 To select your sound source, adjust the
R-14/ UM-2/ C-cellsfor the set.
Source selector to: CD/MP3, FM,
1 Source selector: CD/MP3, FM, MW or
! p � 3.5 mm stereo headphone socket
Y When inserting new batteries,do not try to mixor MW.
OFF
Helpful hints:The speakers will be mutedold batteries with the new ones.
� selects CD/MP3, FM or MW source of2 To switch off the set, adjust the
when headphones are connected to the set.
Y Remove the batteries if the set is not to be usedSource selector to OFF position.
sound
@ AC MAINS~ � inlet for power cord for a long time.
� power off switch
# Voltage selector � adjust to match theAdjusting volume
Batteries contain chemical substances,so
2 2; � starts or pauses CD/MP3 playback local voltage 110/220V before plugging in the
Adjust the sound with the VOLUME control.
they should be disposed of properly.
set
� selects the next/previous track
Using AC power
CAUTION Radio reception � fast searches forwards/backwards
1 Check if the power voltage, as shown on
1 Adjust the Source selector to FM or(press and hold the button) Use of controls or adjustments or
the type plate located on the
performance of procedures otherMW to select your desired waveband.
PROG � programs tracks bottom of the set, corresponds to your
than herein may result in unsafe2 Turn TUNING to tune to a station.
local power supply. If it does not, consult your
9 � stops CD playback;operation.
dealer or service center.
� erases a CD program Helpful hints:
2 If your set is equipped with a voltage selec-
3 Display � shows the CD functions To improve radio reception
Power Supplytor, adjust the selector so that it matches
Y For FM, extend, incline and turn the telescop-
4 MODE � selects different play modes:
with the local power supply.Whenever convenient, use the power supplyic antenna for best reception. Reduce its
e.g. REPEAT or SHUFFLE (random
cord if you want to conserve battery life.3 Connect the power cord to the length if the signal is too strong.
order)
Make sure you remove the plug from the setAC MAINS~ inlet and the wall socket.The
Y For MW, the set uses a built-in antenna.
5 ALBUM + � For MP3-CD only: selectsand wall outlet before inserting batteries.set is now connected and ready for use.
Direct this antenna for best reception by
albums
4 To switch the set off completely, withdraw theturning the whole set.
Batteries (not included)
power cord from the wall socket.
6 OPENYCLOSE � opens/ closes the CD
1 Open the battery door and insert 6 batteries,
door 5 Install the unit near the AC outlet and where
type R-14, UM-2 or C-cells, (preferably
the AC power plug can be easily reached.
alkaline) with the correct polarity as indicated
7 TUNING � tunes to radio stations
by the "+" and "�" symbols inside the com-Y Disconnect the power cord from the wall
8 VOLUME � adjusts volume level partment (See 1).socket to protect your set during heavy
thunderstorms.
2 Replace the battery door, making sure the bat-
teries are firmly and correctly in place.The set
The type plate is located on the
is now ready to operate.bottom of the set.
Helpful hints:
� To avoid unnecessary energy consumption,
always adjust the Source selector toOFF
after using the set. |
ACEC
PHILIPS
