Installation
Any electrical work required to install this applianceThe sink plug must not be in place when the machine is
should be carried out by a qualified electrician ordraining as this could cause the water to siphon back into the
competent person.machine.
Any plumbing work required to install this appliance
should be carried out by a qualified plumber or competent
person.
Remove all packaging before positioning the machine.
O 18O 21
If possible, position the machine next to a water tap and a
drain.
+ 2 m maxmax 100 cm
Levellingmin 30 cm max 100 cm
CS10
Good levelling is essential for correct closure and sealing of
the door. When the appliance is correctly levelled, Attention!the door will
not catch on the levelling spacers on either side of Our theappliances are supplied with a with a security device
cabinet. If the door does not close correctly, loosen to protect or tightenagainst the return of dirty water back into the
the adjustable feet until the machine is perfectly machine.level.
If the spigot of your sink has a "no return valve"
Water supply connectionsincorporated this can prevent the correct draining of your
This dishwasher must be plumbed into a cold water supplydishwasher.. We advise you therefore to remove it.
The water pressure must be within the limits given in the
Electrical connection
"Technical specifications" (Instruction Book - Part .2)
Your local Water Authority will advise you on the averageThis appliance must be earthed.
mains pressure in your area.The manufacturer declines any responsibility should this
safety measure not be observed.
The dishwasher features fill and drain hoses which can be
turned either to the left or the right to suit the installation.If the plug that is fitted to your appliance is not suitable for the
Do not use, for connection, old hoses which have beensocket, it must be cut off and the appropriate plug fitted.
used in another appliance.
Important
The locknut must be correctly fitted to avoid water leaks.
The wires on the mains lead are coloured in accordance with
Avoid bends or kinks in the hose which could prevent the or following slowcode:
down the water supply.
Green and Yellow -Earth
If the machine is connected to new pipes or pipes which have
Blue-Neutral
not been used for a long time, you should run the water for a
Brown-Live
few minutes before connecting the inlet hose. This will prevent
deposits of sand or rust clogging the inlet hose.If you fit your own plug,
the colours of the wires
Water outlet hose connectionin the mains lead ofE
your appliance may not
The end of the drain hose can be connected in the following
correspond with the
ways: 13A
markings identifying the
1. To the sink outlet spigot, securing it if necessary with a L
terminals in your plug.N
clip.
2. Hooked over the edge of the sink using the special
curved plastic guide if provided( ).
3. To a stand pipe provided with vent-hole, minimum
internal diameter 4 cm.
CE04
123
21
Omin 4 cm
OProceed as follows: 18
1.Connect the Green and Yellow (earth) wire to the terminal
in the plug which is marked with the letter "E" or the earth
symbol or coloured green and yellow.
max 100 cmmin 30 cm max 100 cm
CS092.Connect the Blue (neutral) wire to the terminal in the plug
which is marked with the letter "N" or coloured black.
The waste connection must be at a height of between 30 cm
(minimum) and 100 cm (maximum) from the bottom of t3.heConnect the Brown (live) wire to the terminal in the plug
dishwasher. which is marked with the letter "L" or coloured red.
The drain hose can face either to the right or left The of plug themoulded onto the lead incorporates a 13amp BSI362
dishwasher fuse. Only ASTA or BSI fuses should be used.
Ensure the hose is not bent or squashed as this could The preventplug must not be used if the fuse cover/carrier is lost. The
or slow down the discharge of water. cover/carrier is indicated by the coloured insert at the base of
If you use a drain hose extension it must be no longer the plug.than 2
metres and its internal diameter must be no smaller A replacement than thecover/carrier must be obtained from your local
diameter of the hose provided. Service Force Centre.
Likewise the internal diameter of the couplings used for
connections to the waste outlet must be no smaller than the
diameter of the hose provided.
7 |
ACEC
TRICITY BENDIX
