BVM-D20F1A/D20F1E/D20F1U/D24E1WA/D24E1WE/D24E1WU
Location and Function of Parts
To switch each function between on and off or
Monitor 1Monitor 2between enable and disable, change pin connections inBKM-10R Monitor Control Unit (Optional)
Chapter 1 OverviewREMOTE 1REMOTE 1the following way.This manual explains the location and function of partsChapter 1 Overview
ON or enabled: Short each pin and pin 9 together.
and controls of the optional BKM-10R Monitor
ININOFF or disabled: Leave each pin open.
Control Unit. The explanation applies to the optional
BKM-11R Monitor Control Unit.
9 ISR (Interactive Status Reporting) connector
(female, D-sub 9-pin)
Connect to the ISR system.1 Monitor memory card insertion slot
OUTOUT!1 CONTROL UNIT connector (female, D-sub 9-5 POWER switch
pin)
6 DEGAUSS button
Connects the BKM-10R Monitor Control Unit using a
cable with D-sub 9-pin plugs such as an RCC-5G/10G/7 DISPLAY UNIT
connector (rear)
30G (not supplied) or the cable supplied with the
Cable with D-sub 9-pin plugs (not supplied)BKM-32H/34H Monitor Control Unit Attachment Kit.2 SHIFT button
3 Function buttons8 Numeric keypad
8 REMOTE 2 connector (female, D-sub 9-pin)4 Menu operation9 MANUAL adjustment
buttonsbuttons and knobs
Forms a parallel switch and controls the monitor
externally. The pin assignment and factory setting
function assigned to each pin are given below.
1 Monitor memory card insertion slot4 Menu operation buttons
51
Insert the BKM-12Y Monitor Memory Card (optional).
MENU button: Press to display the monitor
For inserting/ejecting the monitor memory card, see pageUPMENUmenus.
9620.
UP/DOWN buttons: Press to select the
Pin numberFunction2 SHIFT buttonDOWNENTERitems and setting values.
1Set input signal channel 1 (numeric keypadPress to select one of the two functions designated to
function)the function buttons 3.
2Set input signal channel 2 (numeric keypadEach time the SHIFT button is pressed, the LED turnsENTER button: Press to confirm the itemsand values entered (Ent button on the
function)on (SHIFT ON: lit in amber) and off (SHIFT OFF).numeric keypad 8 has the same function).
3Select sync signal (SYNC button function)SHIFT OFF: The functions indicated above the
4Set the screen to monochrome, or set forfunction buttons can be used (the LED of theFor more information about menu operation, see OBasic
automatic switching based on the input signalfunction button lits in green).Menu Operations� on page 22.
(MONO MODE button function)SHIFT ON: The functions indicated below the
5Safe area on/off (SAFE AREA buttonfunction buttons can be used (the LED of the5 POWER switch
function)
function button lits in amber).Press to turn on/off the monitor. By setting with the
6, 7Not connectedADDRESS menu, it is possible to turn on/off the
8Tally lamp on/off3 Function buttonspower of the specified monitors only, or of all
9GroundChange the operation conditions for the monitor.monitors at the same time.
Each time the button is pressed, the LED turns on and
All pin function assignments can be changed with theturns off, and the operation conditions are changed.For information about the ADDRESS menu, see OSelecting
REMOTE menu.Each button has two functions. Select one of the twothe Monitor to Control N ADDRESS Menu� on page 59.
functions by pressing the SHIFT button 2. When the
6 DEGAUSS button
For information about the REMOTE menu, see O [C2]SHIFT button is set to ON, the LED lights in amber,
Assigning the Remote Control Functions (SET UP 2) Nand when the SHIFT button is set to OFF, the LED ofPress to degauss the CRT (every time the monitor is
REMOTE Menu� on page 40.each button lights in green.turned on, the CRT is degaussed automatically). To
degauss again, wait for more than five minutes.
For the functions of the function buttons in case of SHIFT(continued)
OFF and SHIFT ON, see pages 17 and 18.
1415
1-11 |
ACEC
SONY
