RECORDING
" To check the (remaining) recording time, press DISPLAY.3 Press AUTO/MANUAL to switch between auto and manual
English
(This can also be done during recording)track numbering.
9 If Auto is selected (preferred), AUTOTRACK appears on
3 To stop recording, press STOP on the CD Recorder/Player.
the display.
9CD-SYNC and RECORD go out.
" AUTO: The track number is automatically incremented after
" To interrupt recording, press PAUSE.a silence on the original of at least 3 seconds.
9RECORD starts to flash. To resume, press PLAY on the
" MANUAL: Track numbers can be incremented manually by
CD Recorder/Player.
pressing §. (minimum track length is 4 seconds.)
After recording the display will show UPDATE for several(This can also be done in AUTO mode)
seconds.
" Track numbers cannot be changed after recording.
Note:
4 With the recorder stopped, press RECORD to enter Record
- The CD Recorder/Player will not start until it recognizes
standby mode.
a digital signal. Although the reaction time is less than
9RECORD will flash
200 milliseconds, the very beginning of the music may
sometimes not be recorded. If this happens, you can startRECORDERASETRACKOVERDUALTRACK
FINALIZE CD SYNCSRC
the recording manually (see digital recording -
DUBB 1SHUFFLESCANSHUFFLE
unsynchronized).
AUTO TRACKTOTAL REM TRACK TIMETOTAL REM TRACK TIME
- Recordings from DAT or DCC will only stop after 20 seconds
silence. 5 Play the source first to set the optimal recording level on
the CD Recorder/Player.
6 Press REC LEVEL (+ or -) repeatedly until all the blue
Analogue recording from an external source
segments on the Record/Play level bar light up continuously
OPENRECORDbut the red segments do not during the loudest passages.
CLOSE
DUBB 1OVERCD SYNCTRACK
SCANTRACK9 The display will show -3DB or 0DB or 3DB or 6DB
REMTIMETOTAL
PAUSE DIGREMTIMEOPENTOTAL
CDREPEAT 1CLOREWSRITEAB7 Stop the source.LEPAUSE
REPEAT 1
COMPACT DISC RECORDER CDR765
DISPLAY
SOURCEStart analogue recording
REC LEVEL
DUALDISPLAY
PHONES1 To start recording, press PLAY on the CD Recorder/Player
and immediately start the source.
9RECORD lights continuously.The track number and
recording time used appear on the display.
Only make analog recordings if digital recording is not
possible." To record a 3-second silence at the start of a track,
press PAUSE.
Preparing for analogue recording
1 Make sure the disc is absolutely free of scratches and " To check the (remaining) recording time, press DISPLAY.
dust particles.(This can also be done during the recording)
2 Press SOURCE repeatedly until:2 To stop recording, press STOP on the CD Recorder/Player.
9ANALOG appears on the display.
9RECORD will go out.
FINALIZE CD SYNCSRC
DUBB 1SHUFFLESCANSHUFFLE
AUTO TRACKTOTAL REM TRACK TIMETOTAL REM TRACK TIME" To interrupt recording, press PAUSE.
9RECORD will start to flash. Resume at step 1.
PAUSE DIG ANALOGOPT PROG REPEAT 1PAUSE PROG REPEAT 1
After recording the display will show UPDATE for several
seconds.
" If necessary, press DUAL to switch off the DDUUAALL mode;
DDUUAALLwill no longer appear on the display.
Note: With AUTOTRACK on, the recorder will stop
RECORDERASETRACKOVERDUALTRACKautomatically after a 20 seconds silence.
FINALIZE CD SYNCSRC
DUBB 1SHUFFLESCANSHUFFLEWith AUTOTRACK off, the AUTOSTOP mode is disabled.
AUTO TRACKTOTAL REM TRACK TIMETOTAL REM TRACK TIME
16 |
ACEC
PHILIPS
