RECORDING
� MANUAL starts to flash and the display shows REC
Manual recording from external CD player
EXT MAN followed by WAIT. After a few seconds
PRESS RECORD followed by the remaining time and
EASY JOGtrack number appear on the display.English
CANCEL/DELETE PLAY/PAUSESTOPOPEN/CLOSSTORE/MENU
CDEREM REC TIME TRACKTOTAL REMTRACK TIMESTEPENTER
AUDIO CD PLAYBACK
SYNCMANUALRECORDPROG
OPEN/CLOSEPLAY/PAUSESTOPRECORDINGDIGITALICDCHANGERCDSHUFFLEALL
FINALIZEERASEEXT SOURCEREPEAT
TYPERECORDOPTICALIRWRW
ANALOGSCANTRACK
CDR
4 Play the source first to set the optimal recording level on
the CD recorder.AUDIO CD PLAYBACK
5 Rotate the EASY JOG/ENTER key until, on the Record/Play
PROGSHUFFLEDISPLAYSCROLLREPEATDJ MODE
Level bar, all the blue segments are alight, but the red
segments do not light continuously during the loudest
passages.
Important:� Display shows _XX DB (Decibel, e.g. -3DB).
- Recording from CD-changers should always be started in the
6 Stop the source.
Auto-Start mode.
- Only make analog recordings when digital recording is not
Start manual recording
possible.
1 To start recording, press RECORDING-RECORD on the CD
Preparing for manual recording recorder and immediately start the source (from Pause or
Stop-mode).
1 Make sure the disc is absolutely free of scratches and dust�lights continuously. The track number and recording
particles.time left appear on the display.
2 Press EXT(ernal) SOURCE repeatedly until (depending on theYIf CHECK INPUT message also flashes, the digital
connection used):connection is incorrect.
� DIGITAL I, OPTICAL I or ANALOG lights up and
DIGITAL 1, OPTICAL or ANALOG appears on theYTo record a 3-second silence at the start of a track, press
display.PAUSE on the CD recorder before starting the source.
REM REC TIME TRACKTOTAL REMTRACK TIMESTEP
YTo check the total remaining recording time, press DISPLAY
on the CD recorder. (This can also be done during the
recording.)SYNCMANUALRECORDPROG
DIGITALICDCHANGERCDSHUFFLEALL
RWRWOPTICALIREPEAT
ANALOGSCAN TRACK2 To stop recording, press STOP on the CD recorder.
� UPDATE lights up and goes out.
YWhen Auto Track is On (default setting), track numbers will
automatically be increased during recording. Y If STOP was pressed within 3 seconds after RECORD, no
recording will take place.
YTo switch off the Auto Track function you have to enter
Menu mode.Y To interrupt recording, press PAUSE on the CD recorder.
If you wish to increase track numbers manually, pressstarts to flash. Press PAUSE again to restart recording.
TRACK INCR(ement) on the remote control. For further( A new track will always be made.)
instructions see Menu mode.
After recording the display will show UPDATE for several
ON (AUTO): The track increments are automatically taken overseconds.
from the digital source material or after 2.7
Note: With AUTO TRACKON, the recorder will stop and go
seconds silence during analog recording.
to REC STANDBY for 1 minute and then goes to Stop
OFF (MANUAL): While recording track numbers can bemode automatically. Recordings from DAT, DCC or
incremented manually by pressing TRACKrecordings made analogously will stop after 20 seconds
INCR(ement) on the remote control.silence. With AUTO TRACK OFF, the auto stop
(Minimum track length is 4 sec.) (This canmode is disabled.
also be done in Auto track ON mode.)
Important:
Y Track numbers cannot be changed after recording.If you want to play the recorded CDR disc on any
regular CD player, it must first be finalized. See
Note: Auto track works only with Consumer Sources with afinalizing discs.
digital output signal according to the IEC 958
(consumer part) audio standard.Finalized CDRW discs play only on CDRW compatible
CD players.
3 With the recorder stopped, press RECORDING-TYPE five
times to enter the Manual Record standby mode.
21 |