Q u i c k S t a r t G u i d e
15. Roll the tape. Make sure the lead vocalIf you want to apply an external analog or
track is turned up and center-panneddigital effect to only one channel, use the INSERT
between the left and right sides.jacks for channels 1�12 (only). This is a TRS
16. Click on the EFFECTS button in the Bankjack specially configured as a combination
Select Section to select Fader Bank 3.analog Send/Return connection point (Tip =
Send, Ring = Return, Sleeve = Ground). With
nothing plugged into the INSERT jack, the
send signal is directly connected to the return
MASTERSSHIFTpin via the normalling jack.
Y The Insert Send signal comes after the
1-2425-48
Mic/Line preamp and TRIM control, and just
before the analog-to-digital converter.
MIC/LINETAPE IN
(TRACK)(MONITOR)Y Connect the Send signal to the input jack of
the external processor.
49-72
Y Connect the output from the external
processor to the Return connection of the
EFFECTS
INSERT jack.
BANK SELECT
SEND to processor
ringOtip�
17. Make sure FX1�4 are assigned to the L-R(TRS plug)
tipsleeve
bus. Click and drag the FX1 fader up to hear
the Baritone harmony. You can pan it to the
left by clicking on PAN in the Master V-PotThis plug connects to one of the Oring�
mixerOs Channel Insert jacks.RETURN from processor
Section and then clicking and dragging the
FX1 V-Pot fully counterclockwise.
18. Click and drag the FX2 fader up to hear
If you want to route a number of channels to
the Mezzo harmony. You can pan it to the
a single external effect, use an aux send. The
right by clicking and dragging its V-Pot
Digital 8YBus has a total of 12 aux sends that
fully clockwise.
can be used for effects or monitors. The first
19. Click and drag the FX3 and FX4 faders up
eight aux sends are routed to the internal
to hear the reverb effect on all three parts.
effects cards as well as the AUX OUT jacks.
You can use an internal effect and its
There are several other control modes
corresponding aux send simultaneously.
available in the IVL Vocal Studio. Manual Mode
However, you can choose not to use an internal
and SmartChord Mode require a MIDI input
effect by leaving its associated FX Return
from a keyboard or sequencer to operate. Pitch
control (Fader Bank 3) turned down (or turn
Shift Mode allows you to set a chromatic
the PLUG-INS off in the Fat Channel). The Aux
interval between the lead vocal and the
Send on the rear panel can always be used to
harmony voices to create true parallel
send a signal to an external effect.
harmonies. In addition, there is anotherAs an example, letOs say you want to use
operating mode called Pitch Correct, which you
Aux 2 as a send to an external digital delay.
can use to fix out-of-tune vocal parts. More
Y Connect AUX 2 on the rear panel of the
information is provided in Appendix E in the
Digital 8YBus to the input of the external
Digital 8YBus OwnerOs Manual, and in the IVL
digital delay.
Vocal Studio OwnerOs Manual which you
receive when you purchase the IVL Vocal
Studio software.321
+48V+48V+48V
PHPHPH
Using External EffectsMICMICMIC
WeOve built in the most common effects
packages that youOre likely to use for
recording, post-production, or live sound
LINE INLINE INLINE IN
purposes. However, some people have favorite
effects boxes that they like to use, perhaps
INSERTINSERTINSERT
even to produce a signature sound. The use of
external effects is straightforward.
AUXAUXAUX
321
23
General Guidelines |
ACEC
MACKIE
