7 - Advanced operations
Pressing ts anhe dt keys simulta-to another facility using the DA-78HR, and set up the
neously returns the output patocthhbeary m achine in exactly the same way as the original
to the normal state.at home. Of course, there are many other uses for this
facility.
The meters display the current
Track 8
Track 7assignments of tracks to the ouThtep uste ttings stored on the tape do not affect the
Track 6
channels. In this case, each mreecoterr ded audio data.
Track 5
Track 4shows the assignment status of the
To save the current settings to tape:
Track 3correspondingly-numbered output
Track 2
1
channelno (t track), as shown here.Make sure that there is a formatted tape in the
Track 1
recorder before you start to save the settings to
Press SHIFT and one ofRE tC he
tape. The tape must be stopped before you
FUNCTION keys (as described in
start the save operation.
4.1.1, ?Peak meters?) to toggle this meter mode off
and on. The default at power-on is for th2isP mresodse t toSHhe I FbTe key so thatSH tIFhTe i ndicator
on.is flashing, and prMEeNsUs t kheey until the
display shoswystem-s - (SYSTEM--).
7.13Emulation3 Press tShUe B MENU key until the display
showsSAVE. OFF (SAVE OFF ).
The DA-78HR can be set to emulate other DTRS
4 Press tshe key to make the DA-78HR ready
types when interrogated by an RC-898 remote con-
for saving the settings. The display will show
trol unit or other remote control devices (such as the
READY (READY ).
controllers on the TM-D series of TASCAM digital
5 Press ts he key again to actually start the save
mixers).
operation.
1 Press tSHhe IFT key so thatSH thIFTe i ndicator
is flashing, and prMEeNsUs t kehey until the The DA-78HR will automatically search to the
position on the tape where till bhe dea ta w
display shoMwAINTN--s
(MAINTN--).saved, will write the data, and then rewind and
check that the data has been correctly written.
2 Press tShUB Me ENU key until the display
While the data is being written and checked,
briefly shDEv TYows PE (DEV TYPE), fol-
the display sSAVIhows NG (SAVING).
lowed by the current setting.
6 When the save operation has finished correctly,
3 The default is (natDA-78HRurally), but you
the display sdonehows (DONE ). The tape
can use tsh ae nd t keys to select any of the
may now be ejected.
followinda-88g: (DA-88 post-V4 with SY-88
If there is no tape inserted (or the tape has not been
fitted giving all timecode functions when work-
ing as a slave with ID 2 orda-38 gre ater), formatted) when the save operation is readied, the
display shno TAPows E (NO TAPE ).
(DA-88 pre-V4, with track cDA-opy98) a nd
(DA-88 pre-V4).If the tape is not stopped when the save operation is
readied, the displanoty s sthowops (NOT
NOTE
STOP).
None of these emulations provides full control of all
facilities available on the DA-78HR from theI rfe amont ee rror is encountered while saving is taking
control unit. If the remote control unit doepsl nace,ot s tuph-e disill splay whSAVE ERRow (SAVE
port the DA-78HR, seDA-9lect8 as the emulation. ERR).
If the controller does not support the DA-98, select
DA-88 as the emulation.
7.15Restoring settings from tape
7.14Saving settings to tape
This allows you to recall settings stored on tape as
described above (7.14, ?Saving settings to tape?).
This function allows you to store your settings conve-
1 To restore settings, the tape containing the set-
niently on the tape that you have used to make your
tings must be loaded. The tape must be stopped
recordings. This means that you can work at home on
before you start this restore operation.
your project using your own DA-78HR, take the tape
45 TASCAM DA-78HR |
ACEC
TEAC
