DR-MH300SE.book Page 94 Wednesday, November 23, 2005 6:23 PM
Troubleshooting
Resetting
APLEASEB and AWAITB display alternately, or The unit does not operate.
ARESETTINGB blinks for a long time after the power
plug is inserted. Is it a malfunction?0Child lock has been set.
Cancel the child lock. [ P79]
0It normally takes about 40 seconds to prepare before you
0There are cases when the operation is prohibited, depending
can start any operations. Operations cannot be performed on the disc.
during this period.
0If the unit cannot be operated at all, turn off the unit, and
0If the display does not seem to disappear, reset the unit.
Press STOP/CLEAR (o) and STANDBY/ON on the unit then on again. (Lightning or static electricity may cause
malfunction of the unit.)
simultaneously until ARESETTINGB is displayed on the front
display panel.
Or pull out the power plug, wait around 5 seconds and then ALOCKB is displayed on the front display panel, and
re-insert.the disc cannot be removed.
Cancel tray lock using the following method.
Not functioning while AWAITB blinks on the front While holding STOP/CLEAR (o), press OPEN/CLOSE (M) on
display panel.the unit when the unit is in standby mode. AUNLOCKB is
displayed on the front display panel when tray lock is released.
The unit is automatically repairing recorded data that is
unusual. Wait until the time display is displayed. Repairing
may take more than 1 hour.
Playback
The disc tray does not open.No images on the TV screen.
It can be removed by force using the following method.0Check if the video input is displayed.
A Press STOP/CLEAR (o) and STANDBY/ON on the unit Switch the TV (AV TV) with video/audio input terminals to
simultaneously for more than 2 seconds until ARESETTINGB the external input connected to this unit.
is displayed on the front display panel.0Check the output format of the image. Press OUTPUT
B Press and hold OPEN/CLOSE (M) on the unit until the disc FORMAT for more than 3 seconds and the current format
tray opens. (Takes about 30 seconds.)will be displayed on the front display panel. To revert back
to the standard setting, press OUTPUT FORMAT repeatedly
C After removing the disc, press OPEN/CLOSE (M) to close
the disc tray. (The unit will turn off.)while the output format is displayed on the front display
panel. Then press ENTER after AOUT 576IB is displayed.
GeneralImages do not appear on the TV screen or images are
distorted.
No power is supplied to the unit.
Check the output format of the image. Refer to the above
The power cord is disconnected from the socket.mentioned for checking method.
The channel cannot be changed.0 Playback does not start or stops immediately after
pressing PLAY.
Channel cannot be changed during recording.0 ANO DISCB is displayed on the front display panel.
0Place the disc on the disc tray with the playback surface
The remote control does not work.
facing down.
0The setting of the remote control code (1/2/3/4) is 0A disc not compatible with this unit is loaded. [ P12]
inappropriate. [ P80]
0The disc loaded is dirty.
0The batteries may be depleted.Use a soft cloth to clean. [ P13]
0Remove the batteries, re-insert after more than 5 minutes 0The disc loaded is badly warped or scratched.
and then try again. Alternatively, replace with new batteries.
Images are distorted when you start high speed
Dubbing from the Video Cassette Recorder is not search.
possible.
Images are distorted at the point where the playback speed
The external input channel AF-1B setting is inappropriate. changes. It is not a malfunction.
[ P21]
RetroActive Playback does not start.
The on-screen text displayed when playing back on
For HDD, set Setup Menu ALIVE MEMORYB [ P85] I to
this unit is recorded during dubbing.
other than AOFFB.
Set to the following setting. Setup Menu ASUPERIMPOSEB =
AOFFB [ P88] a
94H EN |
ACEC
JVC
