Front panel facilities
For operational instructions, see page indicated in brackets [ ].Input source buttons (DVD, Video 1�5, Tape, FM,
AM, Phono, and CD) [26, 48, 50, 55]
Power switch [26]
These buttons are used to select the input source for the main zone.
Turns on and off the main power supply for the DTR-7.2.To select the input source for the remote zone (Zone 2) or recording
out (Rec Out), first press the Zone 2 or Rec Out button, and then the
desired input source button. The input channel with its indicator lit
Standby/On button [26]
red is output to Rec Out and the one with its indicator lit green is
When this button is pressed with the main power switch turned on,output to Zone 2.
the DTR-7.2 turns on and the display lights up. Press again to return
the DTR-7.2 to the standby state.
Audio Selector button [53]
Standby indicator [7, 26]This button is used to select the type of audio input signal. Each time
pressed, the setting cycles from OAuto� ? OMultich� ? OAnalog�
Lights when the DTR-7.2 is in the standby state and flashes when a
signal is received from the remote controller.and back. When multichannel is not selected, the setting just changes
back and forth between OAuto� and OAnalog.�
Display button [52]
Phones jack [50]
The Display button is used to display information about the current
input source signal. Each time you press the Display button, theThis is a standard stereo jack for connecting stereo headphones.
screen changes to show you different information concerning the
input signal.Upsampling indicator [42]
Lights during upsampling. This function is available when the input
Dimmer button [52]source is Analog/PCM and the listening mode is set to the stereo or
surround (Dolby Pro Logic II only) mode.
Press to set the brightness of the front display. There are 3 settings
available: normal, dark, and very dark.
Remote control sensor [7]
Y The dimmer control for the front display can be performed at the
remote controller.
Tuning / , Preset / , cursor ( / / / ) buttons
Front display[27, 48, 49]
To tune in a radio station, use the / buttons. The tuner frequency
is displayed in the front display and it can be changed in 50 kHz
Rec Out/Zone 2/Off buttons [54, 55]increments for FM and 10 kHz increments for AM.
These buttons allow you to use the DTR-7.2 to output to a remoteWhen FM is selected, you can hold down one of the Tuning buttons
zone (Zone 2) or to another component for recording purposes (Recand then release it to activate the auto-search feature. It will search
Out). Press the Rec Out button to output the audio and video signalsfor a station in the direction of the button you pressed and stop when
to a recording component for recording purposes. Press the Zone 2it tunes into one. When navigating through the menu settings, these
button to enjoy the output from the DTR-7.2 in a different room,buttons move the cursor up or down (or change the highlighted
which is referred to as a remote zone (Zone 2).item).
When either button is pressed, the currently selected input source forTo select a radio station that was stored using the Memory button,
recording or outputting to the remote zone is displayed in the frontuse the / buttons.
panel display. If OSOURCE� is displayed, then the same inputWhen navigating through the menu settings, these buttons select the
source as that selected for the main zone will be output.value or item that you selected with the Tuning / buttons.
To select an input source, press the desired button (Rec Out or ZoneWhen you press the Setup button, the cursor indicators light and the
2) and then press one of the input source button within 5 seconds.Setup button becomes able to be used for setup menu operations.
That source will be output for recording or viewing in the remote
zone.Setup button [27]
To set the Rec Out or Zone 2 output to the source channel, press that
button twice in succession. To turn off the Rec Out or Zone 2 output,Press to enter the setup menu. When pressed, the cursor ( / / / )
indicators light. The OSD menu will appear on the TV monitor as
press that button and then press the Off button within 5 seconds.
Note:well as the front display on the DTR-7.2.
The Rec Out and Zone 2 buttons use the same circuit and therefore
cannot be used at the same time. When Rec Out is selected, nothingEnter button [27]
is output to Zone 2, and vice versa. When Zone 2 is selected, Rec OutPress to display the screen for the selected item in the Setup Menu.
is automatically fixed to SOURCE.
Master Volume dial [50, 53]
The Master Volume dial is used to control the volume for the main
zone. The volume for the remote zone (Zone 2) is independent.
Video 5/Video Cam Input terminals [19]
For connecting a video camera or game device.
9 |
ACEC
INTEGRA
