Index parts and facilities
For further operational instructions, see the pages indicated inRec Out/Zone 2/Off buttons [38-40]
brackets [ ].
These buttons allow you to use the DTR-8.3 to output to a remote
Front panelszone (Zone 2) or to another component for recording (Rec Out).
Press the Rec Out button to output the audio and video signals to a
recording component for recording. Press the Zone 2 button to enjoy
Standby/On button [30]the output from the DTR-8.3 in a different room, which is referred to
as the remote zone (Zone 2).
After plugging in the power cord, the DTR-8.3 turns on and the
When either button is pressed, the currently selected input source for
display lights up, the DTR-8.3 turns on and the display lights up. Ifrecording or outputting to the remote zone is displayed in the front
pressed again, the DTR-8.3 returns to the standby state. In the
standby state, the display is turned off and the DTR-8.3 cannot bepanel display. If OSOURCE� is displayed, then the same input
source as that selected for the main zone will be output.
operated.
To select an input source, press the desired button (Rec Out or Zone
2) and then press one of the input source button within 8 seconds.
Standby indicator [7, 30]That source will be output for recording or viewing in the remote
Lights when the DTR-8.3 is in the standby state and when a signal iszone.
received from the remote controller.To set the output to the source channel, press the desired button (Rec
Out or Zone 2) twice in succession. To turn off the output, press the
desired button (Rec Out or Zone 2) and then press the Off button
Audio Selector button [35]
within 8 seconds.
Press to select the type of audio input signal.
Note:
The Rec Out and Zone 2 buttons use the same circuit and therefore
Input source buttons and indicators (DVD, Video
cannot be used at the same time. When Rec Out is selected, nothing
1�5, Tape, Tuner, Phono, CD, and Net Audio) [31,is output to Zone 2. When Zone 2 is selected, Rec Out is
36, 38, 40]automatically fixed to Source.
Press these buttons to select the input source for the main zone.
To select the input source for the remote zone (Zone 2) or recordingStereo button [32]
out (Rec Out), first press the Zone 2 or Rec Out button, and then
Selects for the stereo listening mode.
press the desired input source button. The input channel with its
indicator lit red is output to Rec Out and the one with its indicator lit
green is output to Zone 2.Surround button [32]
Selects for the Dolby Pro Logic II, DTS Neo:6, Dolby Digital, or
DTS listening modes.
Front display
THX button [32]
Remote control sensor [7]
Selects for the THX listening mode.
Display button [33]
DSP / buttons [32]
Press to display information about the current input source signal.
Switches to the DSP (Digital Signal Processing) modes.
Each time you press the Display button, the screen changes to show
you different information concerning the input signal.
Dimmer button [34]
Press to set the brightness of the front display. There are three
Master Volume dial [31, 35]
Use to control the volume in the main zone. The volume for thesettings available: normal, dark, and very dark.
Y The brightness of the front display can also be performed using
remote zone (Zone 2) is independent.
the remote controller.
Upsampling indicator [57]
Memory button [37]
Lights during upsampling.
Press to assign the radio station that you are currently tuned to a
Pure Audio indicator [32]preset channel or press to delete a previously preset station.
Lights during pure audio playback.
FM Mode button [36]
Press to change the stereo mode from Auto to Mono and vice versa.
Direct/Pure Audio button [32, 35]Each time this button is pressed, the Auto indication turns on and off
Press to switch between the direct and pure audio listening modes.indicating the current mode. If you are listening to an FM radio
station in stereo and the sound cuts out or there is a great deal of
Phones jack [33]noise, switch from Auto to Mono.
This is a standard stereo jack for connecting stereo headphones.
Setup button [43]
Zone 2 Level / buttons [41]Press to enter the Setup Menu. The OSD Menu will appear on the TV
monitor as well as the front display on the DTR-8.3.
Press to enter the mode for adjusting the volume in the remote zone
(Zone 2).
11 |
ACEC
INTEGRA
