Additional Information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with
this component, check the points below. Sometimes the trouble may lie in another component. Inspect the other
components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks
listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work.
The disc table comes back out automatically, shortlyThe settings are not saved in the memory/The
after the disc table is closed.settings are erased.
The disc is dirty or warped.Turning the power off during playback will not save any
\ Refer to ODisc Care� (page 66).changes made in the settings from the Setup screen
menus, or register the last memory function or the
The disc is not placed properly on the disc table.condition memory function settings.
\ Use the disc table guide to align the disc (page 23).\ To register the settings, press STOP 7 to stop
playback and then turn off the power.
Region number does not conform with this unit..........................................................................................................................
\ If the region number on the disc does not match theNo picture.
number on the player, the disc cannot be used (pageConnection is incorrect.
72).\ Check that cord connections are correct and that
plugs are firmly connected.
There is condensation on the operating section of the
player.Player settings are incorrect.
\ Allow time for condensation to evaporate. If player is\ Check that the Component video output selection
near an air conditioning unit, you should move theswitch is set firmly in the correct position.
player (page 67).
.........................................................................................................................Operation (settings) of TV or AV amplifier is not
Playback is not possible.appropriate.
The disc has been loaded upside down.\ Be sure that your TV, receiver, or amplifier is set up to
\ Check that the disc has been loaded with the labelview DVD playback.
side facing up..........................................................................................................................
.........................................................................................................................The screen is stretched or aspect does not change.
mark appears on screen.The multi aspect setting is not appropriate.
The selected function does not operate for that disc.\ Change the aspect setting in the [TV Screen] setting
.........................................................................................................................in the Setup screen Video menu to the screen type
mark appears on screen.most appropriate to the TV or monitor you are using
(page 36).
The operation is prohibited by the player..........................................................................................................................
.........................................................................................................................
The screen is suddenly squeezed when the Setup
Picture playback stops and the operation buttons
cannot be used.screen is opened.
If the Setup screen is opened during playback of a DVD
\ Stop disc playback (press STOP 7), then start
playback again.being viewed in the letter box format, the screen may
switch to the wide screen format.
\ Press POWER on the front panel to turn the player
off, and then turn the power back on again.\ This is not a malfunction. The screen will return to
.........................................................................................................................normal when the Setup screen is closed.
.........................................................................................................................
New settings made in the Setup screen menus while
a disc is playing are ineffective.Picture disturbance during playback or dark.
This is not a malfunction.ADDITIONAL INFORMASome settings can be changed while a disc is playing,
\ This player is compatible with Macro-Vision System
but are not effective. This is not a malfunction.
\ Make the same setting when the player is stopped.copy guard. Some discs include a copy prevention
signal, and when this type of disc is played back,
\ Stop disc playback (press STOP 7), then startstripes etc., may appear on some sections of the
playback again. When playback is resumed, the new
settings should be in effect. Please note that makingpicture depending on the TV.
settings in the Setup screen menus may cancel the
resume function.Discs respond differently to particular player functions
.........................................................................................................................which may result in the screen becoming black for a
When making changes in the Setup screen menus,TIONbrief instant or shaking slightly when the function is
executed.
is displayed.
\ These problems are largely due to differences
There is a Video CD or CD loaded in the player and thebetween discs and disc content and are not
setting that was changed only applies to DVD
malfunctions of this player.
performance..........................................................................................................................
\ The settings will be effective the next time a DVD is
loaded.
.........................................................................................................................
69
En |
ACEC
PIONEER
