20 Initial Setup (contOd)
¨
GUIDE Plus+System Setup
¨
An introduction to the GUIDE Plus+System will appear.
Read this, then press OK to continue through these introductory
1¨REC/OTRSTANDBY
menus.The remaining menus help you set up the GUIDE Plus+
10
System, which provides free TV programming information through
TIMER REC MODE PLAY MODE TV/DVD
the Recorder. See pages 43-47.
MONITORDIMRETURNT/C
First you will be asked about your country, zip code, Cable TV ser-YTV
vice, and Cable Box availability. Use 8CH+ and 9CH- to chooseDISC MANAGER FSSSELECT
2
an answer, then press OK. Use the Number buttons to enter thei
zip code. Follow the instructions on the TV screen.SUBTITLEAUDIOANGLEZOOM
`
If you do not have Cable TV or a Cable Box, skip to step 8.GUIDE/TV
Otherwise, you will set up your Cable Box next.DISCDISCCHCH+
3
When asked to enter your Cable Box output channel: If you used anMENU
RF coaxial cable to connect the Cable Box to the Recorder, chooseOK
channel 2, 3, or 4. (Choose the output channel of your Cable Box.
This may be indicated by a manual switch on your Cable Box.)1-9SYSTEMCHCH-
Or, if you used Audio and Video cables, choose EXT2, EXT 1,STOPPLAYTV VOLUME
CAM 1, or CAM 2. Choose the channel that matches the jacks on�
the Recorder to which you connected the Cable Box.SLOWPAUSE
HkG
Directions for connecting the G-Link cable will appear next. If you
have not connected the G-Link cable to the G-LINK jack on
4
the rear of the Recorder, do so now. Press OK when the cable
is connected and you are ready to continue. See pages 11 and 18.
A list of Cable Box brands will appear. Select your Cable BoxCLEARMUTE
brand, then press OK. If your brand is not listed, select ONot
5
Listed.�
You will be advised to turn on the Cable Box and set it to
channel 2. After doing this, press OK to continue.
6
The Recorder will test codes that allow the G-Link cable to change
the Cable Box to channel 9.
7
A message will ask you to confirm whether the Cable Box
has changed to channel 9. If it does, select Yes. Press OK.
If the Cable Box does not change to channel 9, check all connec-
tions. Select OTest this code again,� then press OK.
Or, choose No and press OK.The Recorder will try a different
code. Repeat this process until the Cable Box changes to channel 9.
OConfirming your settings� will appear. When the information is
correct, choose OYes, end setup,� then press OK.7
8
If the settings are incorrect, choose ONo, repeat setup process,� then
press OK.You will go through the setup again. Change any incorrect
information.
Helpful information about the GUIDE Plus+¨System will appear.CCAABBLBLEBOOX EX
Press OK to continue.
9
A congratulations message will appear, prompting you to select
OWatch TV.� Press OK again.You are finished!
Within a few seconds, the DVD Recorder will turn itself off,Helpful Hints
then on again. When the Recorder turns on again, the GUIDE
¨Y By default,the GUIDE
Plus+System will show Ono data.� This is normal, as the Recorder
¨
Plus+System will appear
has not had time to receive programming data.To use the Recorder
¨first every time you turn on
right away, press GUIDE/TV to remove the GUIDE Plus+System.
the Recorder.To cancel this
feature,turn off the Auto
Press STANDBY yy to turn off the Recorder later. The
¨Display under Review
GUIDE Plus+System data will be available in about 24
10
Options in the GUIDE
hours. When the Recorder is off, channels will change on your
¨
Plus+System.See page 44.
Cable Box.This is normal, as the unit is searching for GUIDE
¨Y The Recorder must be off in
Plus+System information. For best results, turn off the Recorder
¨order to receive GUIDE
overnight so it can receive the GUIDE Plus+System data.
¨
Plus+System data.
Leave the Cable Box turned on. |
ACEC
PHILIPS
